Find a reliable appliance technician in Logan Beaudesert

The inside of machine that locks the door is broken

Tallboy, freezer, hairwash sink, somw cloths and shoes, two printers and a tv

Hey folks, we wanted to convert our main sliding door to an automated one. The gate is installed and works well. I need someone to install the motor , racks etc and power it.

My 2004 Smart ForFour needs some transmission and ABS codes cleared. Couldn't do it with a standard scanner. Codes are: P1895 Transmission : N15/5 (Electronic Selector Module (ESM/EWM)) Actual value above the set value. P1842 Transmission : Transmission speed or vehicle speed cannot be calculated (signal error). P1872 Transmission : Potentiometer 1 Implausible value P1817 Transmission : The value of sensor 'Poti 1' is implausible compared with that of sensor 'B43 (Gear position sensor) P1862 Transmission : Incremental sensor 'Transmission' (1) Signal fault U1431 The current gear is implausible. C1640 Faulty variant coding My clutch actuator was damaged and I replaced it with a used one.

Move out, unwire (hardwired) current oven and replace it with slightly upgraded oven (has 3 pin plug)

We need our heater flue cleaned. Single storey home. Need done asap.

Installing a dryer on the wall

I have recently moved homes and I need help to get my washing machine connected for use in my new space

I want to install two to three eufy computers at my house

Remove cement pizza oven left by previous owners. Is on a cement platform that looks to be cracked down the centre. The base is 110cm x 110cm. It’s approx. 65cm tall. The gate opening to get it out of is approx. 80cm wide.

Install only a new cooktop, a new under bench oven, 2 x ceiling fans with remotes where there are currently lights only, replace faulty outside light with new one that is supplied. Supply and install 5 new power points

Tried mounting myself however was not secure. Steel frame of house I have mount/timber to attach to wall as the space of mount is not the same as wall studs. I also have certain screws but unsure if long enough and if thats the reason it wasnt attaching propley. Just need the dryer on the wall

Remove the existing hills hoist and install new one. I have the hills hoist.

Watching machine not draining, tried to trouble shoot nothing is helping, don’t know if my drainage hose needs replacing or if it’s something else. Not l can’t remove my drainage hose myself because it’s connected inside the. Back cover of the machine and l can’t unscrew that , don’t have the tools.

Have a new kitchen installed and we need a plumber to connect up the Sink & taps & dishwasher under the sink...

Never had a dishwasher where it’s going. Cut out for pipes etc. needs a seperate isolation switch as atm the whole complex needs to be switched off to do any plumbing atm

Tenants have reported that the existing range hood over stove at island bench is too low (at head height) and have requested it be raised. Not only does the vent hood interfere with line of sight, but when cooking, people bump their head on it! Range hood is currently in working order and hardwired and just needs modification. No electrical work required. You will first have to take off the Sheet-metal casing of the flue. This will expose the flue pipe and supports. Once all pipe and supports are visible you can determine with tenants how high they want you to raise the hood vent. You may have to have a custom pipe made after you reduce the length of the vent pipe. After pipe is installed you will have to customise the outer sheet-metal to match the new height and it may require someone with experience and available tools for sheet metal fab to alter the shroud length.

- Disconnect old electric stove - Check 1 sparking power point - Move 1 tv point

Our dryer died and we have had another one delivered. I hurt my back the other day and can’t remove old one and put new one in place. Should be an easy 10 minute job

Fix AC drain to appropriate spot - Due date: Flexible