Find experienced local carpenters in St Kilda East

Kmart bookshelf we need built

Getting an old gas oven replaced by electric. Need a custom made cabinet panel to fit in and match the rest of the kitchen. Currently there are gaps next to the stand alone oven, need those built in. Approximately 880x600x900 area. Please see photos. Kindly quote inclusive of materials.

- build a cupboard door 217 x 220 cm - modify existing kitchen cabinet to make space for dish washer

This wardrobe is approx. 2 M wide by 2.4 tall and 60 deep. It is a build in with just shelves inside. Need someone to remove from current house, and move to new house in the same suburb. Removal is ground floor, easy access. Rebuild is easy access house, wardrobe to be build upstairs.

I need a kitchen bench built. Images and specs attached. I prefer to receive a quote then we can discuss

Thanks. Build plywood shelving over this wall , as shown in photo. Example photo included to give u an idea. All wall coverage. Plywood. Leave a cavity for desk. The Drawing attached is approx and not to scale. The glass doors and the carpet , in the picture, have now been removed. In small apartment. St Kilda East.

2040 x 620 door needs to be trimmed so that it is 2040 x 600. Wooden door

Hey, looking for someone to help convert an enclosed outdoor area into a shed that we can actually use. Please see pics for an idea... Approx area is 2.5m x 1.3m x 2.3m. We don't have materials. Thanks in advance

Need carpenter to help with skirting boards. Boards need to be cut and installed in 4 rooms in our house either today or tomorrow (Saturday 23/3). We’ve already bought the skirting boards new and they are ready to be installed once cut.

Supply and install timber floating floor to two areas to match existing. Floor boards 185x14mm Tas Oak (I think, or similar) Area 01 - rectangular area (image with furniture on it over yellow tongue board) 3200mm X 650/835mm (depending if existing board is retained)X 3200mm) Area 02 - Stair landing (image of irregular shape, white painted board with mat on it) 2300 X 1050mm (max dimensions), plus one stair nosing to finish

Pee stain resulted by pet, we have tried cleaning with cleaning solution with no effect. Help please

Built in bookshelves A) approx 3400 x 1500 x 340mm b) corner bookshelf approx 2500 x 500 / 850 x 250mm spotted gum in style as shown

Design and build shelving that look good, sleek and functional. They need to be built in to carry books. Design should be book 4-5 book shelves that is above the bed and options for design on the sides of the bed. The back wall and one side wall is brick. - Due date: Flexible

Assembly and installation of Mimosa 3.66 x 2.95m Lava Brighton Louvre Panel Gazebo (Bunnings) to small paved backyard (5 x 6 m plus another metre of surrounding garden bed). Pavers may be slightly out of level at gazebo leg points but easily addressed. Does not require fixing to ground / pavers.

Need our deck sanded back and stained, approx 6 x 4meters.

The bottom part of the exterior of my window frame (in the balcony) has water damage. I need a handyman with some timber experience to rebuild it or just cover/protect it. - Due date: Flexible

Stain timber deck Roughly 20sqm 2 Steps - Due date: Before Tuesday, 9 January 2024

custom made and installed wardrobe in bedroom - Due date: Flexible

I am looking for someone to install small ikea galley kitchen. The old kitchen has been demolished. The electrician and plumber have completed first fix. Six cabinets in total. The benches are being done separately and not part of this job. All cabinets are metod. The cabinets are: 2 x base 40cm 3 draws 1x base 80cm 2 doors for sink 1x base 20cm with pullout 1x base for microwave 1 x wall cabinet for rangehood The sink cabinet will require cut out for plumbing & power point. The microwave & range hood cabinets will require cut out for power point. Floor tiling is being installed next 2 days so ideally cabinets are installed between 15 - 24/12 or after 8 Jan. I have included pics of room & design. - Due date: Flexible

Seeking a craftsman who can construct a vinyl record holder tower from copper pipe with a wooden top, as shown in the attached images. Specifications as follows: External frame material: 22mm copper Internal vinyl rail material: 15mm copper All joints to be professionally soldered with minimal solder residue externally visible at the joint. Finish to be polished for a bright and shiny effect that shows off the copper. Lacquer to be applied to seal the copper against oxidisation to maintain its shine. Removable Tabletop: Walnut or Oak Wood, stained and finished to a high standard (also open to alternate suggestions for type of wood). Professionally joined to pipework as shown in image. Top edges routed to create a soft curved edge. Height x Width x Depth: 980 x 410 x 310 mm - Due date: Flexible