Find trusted local electricians in Perth

Looking for a licensed electrician to replace 12 of these sockets with new modern one. supply and install. The price is for changing one socket. Location is Glendalough.

Room 1: replace one halogen downlight with LED downlight. Put in new bulbs in other two light fittings (bulbs to be provided by me) Room 2: replace bulbs in 2 flourescent light fittings (bulbs to be provided by me) Foyer: put in new bulbs in 2 light fixtures Hallway: put in new bulbs in 7 light fixtures Room 3: 6 x halogen downlights to be replaced with led downlights Room 4: 8 x halogen downlights to be replaced with led downlights Room 5: 6 x halogen downlights to be replaced with led downlights Total LED downlights to be supplied and replaced: 21 Others - putting in fresh bulbs (while you have the ladder!) I will provide the replacement bulbs, you just need to supply the new led downlights. The bulbs are 13w 827 bulbs for all light fixtures except the flourscent light fixtures 28W/840 Would like this done on Wed 27th august. based in Subiaco and can provide parking.

Hi I need two additional electrical outlets installed in a loft space - already powered. One is under an air conditioner as shown so access to power should be ok The other is near a desk with an existing outlet on the wall to the left so also hoping access to power is ok installing festoon lights on a balcony as shown … need a ladder - keen for it to zig zag overhead—- from balcony railing overhead to above the glass sliding door … material to drill hooks into is metal . Electrical outlet is already in place for this so can just be plugged in

A round lightbox sign is being installed outside on a metal pillar with a bracket and needs wiring and connection. Work Required: Outside: The lightbox sign will be fixed on the metal pillar using a bracket. Drilling: A small hole needs to be drilled through the pillar so the wire can go inside. Inside: Run the wire neatly up to the top. Connection: Connect the wire to either: The emergency exit light (walking man sign), OR The ceiling light point above. Notes: Very simple job. Just make sure wiring is safe and neat. Reference images (numbered 1, 2, 3, etc.) are attached below for clarity.

Need downlights replaced with LED lights - 6 total Some other lights to be looked at as well. 2 downlights in the bathroom - needing bulbs changed. 2 flourscent light fixtures - needing bulbs changed 10 ceiling light fixtures - needing a second bulb inserted (can supply the bulbs for these, but not the LED light replacements) i dont know what the cost is, so have just put $300 for now

We need an Electrician to wire a lightbox sign. The wiring will cover an approximate distance of 10 meters from the lightbox to the main power source inside the building. There’s no existing plug or outlet. Responsibilities: Run wiring from the lightbox down to the ground, underground beneath the tiles, and into the building. Conceal the wiring along the wall using electric cable covers. Connect the wiring directly to the main power source or board (refer to the attached image for guidance). Ensure all wiring is safe, secure, and up to code.

I am looking for a licensed electrician to rearrange circuits in switchboard to make space, and fault find a tripping pump circuit. Happy to pay for works by the hour and reimburse material. You can provide your hourly rate - the budget here (not sure if it displays or not) is for the hourly rate, not the full job!!! Allow a 6-8 hrs for works.

Four electrical jobs: 1) Replace (functioning) temporary light fitting with double pendant light fitting. 2) Light in laundry is not working, fix and replace temporary light fitting with permanent one. 3) Entry hallway lights on single dimmer switch do not reach full brightness - fix brightness issue. 4) Stairwell light on 2-way switch does not reach full brightness, fix brightness issue.

I need an experienced auto-electrician or caravan/solar expert to help me diagnose/check/remedy my portable solar panel setup. I want to increase solar power input and battery storage to my caravan when I'm travelling 'off grid', so I have setup a portable solar panel system; this is fully separate to the caravan's existing 400w roof-mounted solar panels. The solar power setup that comes with the caravan has 400w solar roof panels that feed directly to the van's lithium batteries via a Redarc Manager 30 BMS. To augment that supply, I have 3 x separate portable solar panels (with a total output of 590w), that I setup when stationary/camping. These panels feed to the caravan batteries via their own regulator/controller; the feed is direct to the batteries, bypassing the van's Redarc management system, so the two systems are not connected. The problem I have is that the portable panels work for a while (delivering increased amperage to the batteries over and above that generated by the van's roof panels) but after a while they seem to cut out and I get zero amps delivery, even in full sun. Could be the MPPT controller/regulator is acting up or some of my connections, not sure! So - I need help with isolating the problem and remedy! If you are good at diagnosis and know one end of a multi-meter from the other, an hour or two on-site should be sufficient for the task. I will have the panels setup ready for inspection.

I have some smoke alarms which need certification certificates for home sale.

Ceiling plasterwork needs to be made good in one room where light fittings have been changed. In a second room the ceiling plaster needs repairing before the light fitting can be replaced.

I have a telephone port in the centre of the apartment that I need troubleshooting to enable NBN connection. I am currently using the telephone port at the back of the apartment. I believe it needs to be jumpered from krone box just outside our apartment door to extend to this port in the kitchen. That way we have 2 working telephone ports.

10 year old new build house with too many circuits all on one breaker. Using the toaster and kettle at the same time causes breaker to go off

I need two light switches swapped with new ones . Roof leaked into them last night. Power is off, so no live work required. I also have the replacement switches. Just swap and go.

I am looking to have either an exterior light installed or failing that, a power point so i can plug my own light in. There is power going to the air-conditioning unit outside that I am hoping can be tapped into. Otherwise there is a powerpoint inside the apartment just inside the sliding door. shown in the 3rd photo Obviously needs to be done by a qualified electrician. I can send a video of exactly what I am trying to acheive

Relocate an NBN wall connection to another location in the house.

Existing smoke alarm beeps all the time

My existing hard wired smoke alarm has broken off the base plate. Existing unit is discontinued. I have a new unit & base already, just need a sparky to install and connect to mains power.

Plummer has checked the hot water system today saying it is an electrical problem, see photo attached

The electrical hot water heater is not heating. It was installed new only 18 months ago so I doubt it is something too serious, but it appears to be an electrical fault between the power supply and the element. Maybe the thermostat? I don’t know. Probably needs an electrician but I am not an expert. Hopefully a quick fix! $175 call-out and diagnosis and will pay for extra time and parts as required!