Cabinet Making Jobs in South Brisbane

Browse through over 500 Cabinet Making Jobs.

See what you could earn

$0

per month

Based on average cabinet making task prices. Actual marketplace earnings may vary

Why join Airtasker

Join Airtasker

Cabinet Making tasks in South Brisbane

Check out what tasks people want done near you right now...

Is that a code on the picture?

Sun Apr 20 2025

about 20 hours ago

Open

Looking for a skilled handyman or cabinet installer to complete the following tasks: 1. Remove the existing built-in vacuum system 2. Remove the existing basin (sink unit) 3. Install a 1.8m wide kitchenette • I will supply flat-packed or assembled cabinets • I will supply the benchtop (from Bunnings) • You will need to cut a hole in the benchtop for the new sink 4. Install a 60cm slide-out recirculating rangehood • Install Cabinet • Power outlet is already available • Recirculating model – no ducting needed 5. Coordinate with plumber (separate job) • Plumbing exists – just needs to be connected after installation • Leave space and mark cut-outs as needed You will need to bring: • Tools (drill, wrench, etc.) • Screws or minor fixings if needed I will provide: • Kitchen cabinets • 1.8m benchtop • Sink & tap • Rangehood

Algester QLD 4115, Australia

Sun Apr 20 2025

about 21 hours ago

Open

We're seeking a professional 3D CAD designer proficient in SolidWorks to produce detailed Water Control System designs from concept sketches and ideas. The initial task will be to design a Water Level Monitoring (WLM) system with the supplied information and image. Ongoing work may be available based on the quality and promptitude of the design. Please note that the design must be in SolidWorks, and the initial task should only be completed if you are available for ongoing work. The WLM system consists of a main pole (assume 50x4mm tube) which is fixed to the ground and supports the stilling tube, electrical cabinet (300x300x150mm, centre 1.6m from ground), and solar panel (397x280x25mm, 2m from ground with latitude and direction adjustment). The stilling tube extends to the bottom of the canal and must be large enough to house the 27mm diameter sensor and have an adjustable angle to suit the canal. The solar panel and sensor cables must have minimal exposure and remain inside the pole and tube as much as possible before entering the cabinet. All components are to be aluminium. Please develop a 3D model of the entire system, except for the electrical components. Include simplified models of the solar panel and cabinet as references. Detail electrical cable provisions. This task has a limited budget, as we are interested in what can be produced in a restricted timeframe.

Thu Apr 17 2025

3 days ago

Open

I have a small space in my house where a desk is currently set up. The area is over crowded and unusable because of the lack of storage. It’s a narrow space so finding a desk and storage options have been difficult. Therefore, I am looking for someone to help me design a user and storage friendly office space in this area. I am thinking an L shaped desk along the back wall with some shelves where the brown bookshelf is currently location, but I am open to design ideas. No idea if costings or what is required for this kind of job so please let me know!

Mount Gravatt QLD 4122, Australia

Wed Apr 16 2025

4 days ago

Open

I’m looking for someone to help assemble a few pieces of furniture tomorrow in Brisbane CBD: • 1 desk table • 1 TV cabinet • 2 side tables All from Temple & Webster. I reckon it’s a 1.5-hour job max with the right tools. Let me know if you’re available and what your rate is. NO PARKING AVAILABLE Thanks!

Brisbane CBD QLD 4000, Australia

Tue Apr 15 2025

6 days ago

Open

Draws are already done, just need the cabinet part completed. The instructions are in Chinese.

Heathwood QLD, Australia

Mon Apr 14 2025

7 days ago

Open

I want my timber bookcase and tv cabinet painted white

Sun Apr 13 2025

8 days ago

Open

Cut width of a pre-made cabinet by 6cm. Top & bottom boards need to be cut 3cm left & right and repaint the cut sides, and 5 glass need to be cut.

Sat Apr 12 2025

8 days ago

Open

Corner door cabinet repaired or replaced, 1 cabinet door repaired or replaced

Woodridge QLD 4114, Australia

Wed Apr 09 2025

12 days ago

Open

Browse all tasks

Last updated on 20th Apr 2025

How to earn money on Airtasker

Job opportunities that find you

Set up notifications and be alerted when a nearby, well-matched job is posted. Let customers book you directly by setting up a listing. Provide a great service and work with them again with Contacts.

Set your price

Found a job you’re up for? Set your price and make an offer. You can adjust and discuss it later if you need to.

Work. Get paid. Quickly.

When tasks are complete, request for payment to be released and money will appear in your account instantly.

Post a task

We've got you covered

Whether you’re a posting a task or completing a task, you can do both with the peace of mind that Airtasker is there to support.

Airtasker’s insurance cover

Cabinet Making Jobs in South Brisbane

Browse through over 500 Cabinet Making Jobs.

See what you could earn

$0

Cabinet Making tasks in South Brisbane

I need a key or replacement for an Excalibur filing cabinet

Remove Vacuum System & Basin, Install Kitchenette + 60cm Rangehood

3D CAD of Water Control Systems

Cabinet maker required for desk design and install

Assemble a few pieces of furniture

Chest of drawers flat pack

Tv cabinet and bookcase repainted

Modify a pre-made cabinet - Lidcombe NSW

2 kitchen cabinet doors repair corner door