Find a reliable appliance technician in Caulfield South

I’m looking for an experienced cabinet maker, carpenter, or handyman to assess and potentially remove a brown laminate layer under my kitchen benchtop. This layer currently obstructs my dishwasher space, and I need it removed to allow for a new dishwasher installation. The laminate appears to be a finishing layer attached to the underside of the benchtop. I’d like the successful applicant to assess the setup and remove the laminate layer carefully, ensuring no damage to the surrounding benchtop or cabinetry. Requirements: • Expertise in cabinetry, carpentry, or kitchen fittings. • Tools such as a putty knife or chisel, heat gun (if necessary to soften adhesive), and any protective tools for safely removing laminate. • Knowledge of adhesive removal techniques to avoid damaging the underlying surface. • Careful attention to detail to ensure the surrounding benchtop remains intact. • Ability to clean up after the job and leave the space tidy. This job is estimated to take around 1-2 hours, including the assessment and removal of the laminate layer if straightforward.

General maintenance of a Haier front loader. It's working but has a couple of small issues that can hopefully be fixed: -door seal plays up, I need to hold it closed for lock to engage -clothes occasionally come out still soapy -machine occasionally refills with water after cycle

Blocked dishwasher water would go down

Existing pump stopped working. Need to disconnect it from the pipe (see red circle) and pull back the cable through the conduit (about 2-3 metres away, see green circle). Then put in new pump, feeding its power cord through the conduit again. Finally, it looks like this is the pump that is currently there: https://www.tecnoplastic.com/mouseul.html I can't find anywhere that sells it in Melbourne - installer might need to recommend a suitable replacement.

Needs to convert the BBQ to fit natural gas (see links to the BBQ and the conversion kit below). There's a gas outlet just next to the BBQ - see attached photos. The installer should provide a certificate of compliance for home insurance purposes. The BBQ: https://www.beefeaterbbq.com/en-au/barbecues/free-standing/bmg1241bb/ Natural Gas Conversion Kit: https://www.beefeaterbbq.com/en-au/bbq-accessories/installations/bng1200/

Asko front loading washing machine is not draining water. Need someone to pull washing machine forward and inspect the drain hose to check it's clear of blockages or diagnose if pump is malfunctioning. Previously showed error code 7.

We have a Fisher and Paykel 90cm series 7 integrated insert rangehood model HP90IDCHX4. The motor seized and we have taken delivery of a new unit. We require the old unit to be removed and the new unit installed.

help me set up my new dryer Already unboxed and in place

The Laawn Mower starts and only run for a few seconds. I have replaced the sparks plug and air filter. I do believe it might be a carburetor cleaning job. Thanks.

Install smoke alarms on ceilings

My washing machine is working well but is leaking water, it could be a simple fix but I’m not sure

My fridge is not cooling

My fridge only the light is working not cooling. Adjusted the temperatures but still not working

my house has electric window has problem. it can fully open when I pressure open button but the close button I press its working but stop half way can’t fully close

Need the gas safety check done

Install oven flew case. Electrics and any other installation not required. Just the case on the outside

Smeg dishwasher error code 05 E5 – Water fill issue. Kinked hose or inlet valve fault.

The washing machine smells like dirty water because I think it is full of water where it collects stuff ( no idea what the compartment is called - see picture) we can not get it opened so not sure if something stuck or it has heaps of water so the pressure from that is stopping it from being able to be opened.

Washing machine door won’t open

We have moved house today. Removalist installed the washer for us however it is not draining correctly. Error keeps happening and filter keeps filling / overflowing. Need help to rectify this.