Find a local excavator service in QLD

Boring a 3 meter wide hole under drive way. I need a sleeve for a sullage (grey water) hose.

Boards are borer damaged in front bedroom and at least one board is cracking and may need replacing. The house is on poles so access to assess the floor from under the house is possible. We live interstate and our granddaughter lives in the house . Extent of job unknown so budget entered is to fill the requirement only

We are installing a brick fence and we need to run an electrical conduit under a driveway for lights and gate motor. I need a horizontal bore between 30-100mm size for the pipe/electrical cabling. This driveway is approx 5meters wide.

I have a 1986 Honda Cub 50. I am looking to get more power so I’ve purchased a Kitaco Light Bore kit to take it up to 88cc. This is a low-cost bore-up kit that allows the stock cylinder head to be used without modification. I have purchased the necessary parts I just need it installed.

We are building a new house in Thornlands and looking for someone to do the fence between us and our neighbors. Would prefer colorbond style one. Roughly $140 per lineal metre 1800mm high fence.

8 holes to bore - (4 on each pole) must have own drill that can handle the task. 10 mm bore bit. Stair rail already assembled.

VAG CDAA engine 1.8 TSI still in car, head removed, pistons still in. Need bore measurement on all 4 cylinders to verify condition and sizes for replacement pistons. Nominal diameter 82.51mm. Can crank it to expose bore. Want to verify it is worth with proceeding with piston removal and ongoing fixing. Car is in the garage, power available for additional light. I have LED overhead light.

I have ugly light fittings that look like this at my house and I just bought a chandelier that needs to be hung . - Due date: Needs to be done on Saturday, 20 January 2024

Holes to go through ceramic tiles into (dry) concrete pool edge for installation of 1.8 m long, 38 mm dia rail beside pool Due date: Before Friday, 19 January 2024

I have an under bench washing machine and need a hole bored in bench so waste hose can exit and reach sink - Due date: Flexible

I need a holes bored under a 2 meter footpath to run some water line for a outside tap - Due date: Flexible

The switch of the bore is rusty and need a replacement. - Due date: Flexible

Note: Please only quote if you have prior experience with this issue (please advise). Happy for you to quote an alternative approach. We noticed some yellowing of leaves and a branch snapped off easily. The hole in the branch looks to be from borer activity. Not sure how much of tree is affected, it may just be a small part. Scope is to cut out all dead/dying and affected branches from Murraya hedges back to as close to main trunk as possible. Only to be done where really needed. Spray all foliage (hedges ok both sides of house) with Cocky or similar systemic insecticide Place Initiator tablets in the soil at the base of each Murraya hedge (both sides of house). Remove and dump all rubbish (we have waste vouchers). - Due date: Before Wednesday, 7 June 2023

termite and borer treatment of an old one bed flat in Auchenflower - Due date: Flexible

Howdy! Just looking to bore a hole under a STD driveway so that I can run some 19mm Poly pipe irrigation underneath it. Thanks - Due date: Flexible

I need to bore a hole of the entry door I can install lock by myself. - Due date: Flexible

Need auger holes and footings excavated as shown in engineering drawing - Due date: Flexible

Needing Murraya bush treated for wood borer and hedged backs x2 - Due date: Flexible

We have to install some Bollards in a garden bed at Brisbane Motorcycles at Caboolture. we will need 3 to 4 900 deep x 450 wide bored piers put in (vacuum unit would be best) need someone to oversee the Vacuum of holes and then do the concrete works - Due date: Before Tuesday, 9 August 2022

2006 Ford Focus XR5. Motor cooked, can tow the car to your premises if preferred. Absolutely no hurry, work on it at your leisure. - Due date: Flexible