Find experienced local carpenters in Annandale NSW

Need to move French- door fridge from front of house, down the hallway and two steps, needs to be *hoisted/lifted* over countertop (90cm approx). Need to remove doors off fridge (or, i can do it). Remove the mounted kitchen cabinet and re-install after fridge for fridge to be moved (pic attached for reference). Measurements (without doors on fridge) H175xD61xW83 126kg with doors (unsure of weight without doors) Need protective covering

Cast iron bath needs sanding and re finishing as well as a new coat of paint. Minor regrouting needed. Looking for someone handy who knows how to do this job well Please include all consumables in your estimate ta

Prepare and stain wooden deck - 6 x 2 mtrs. Easy access, flat surface.

We need some shelving installed under our kitchen bench top. Around 80x80 x30cm dimensions. Split into an upper and lower shelf. Ideally we need the black colour matched as closely as possible, but plain shelf design is ok.

I have a small studio apartment and want to maximise the storage capacity by having some cabinetry installed around my Murphy bed and above my desk. Nothing fancy but will need a bit of planning to get the most out of the space.

Replace or repair rotten timber in fixed window. See images.

** update 24th dec to Drawing and requirements Polyurethane doors colour tbc with slim shaker 20mm*** only respond if experienced in this area of cabinetry have had bad experiences and don’t need anymore Looking for these cabinets to be made stylish but simple see drawings for detailed information with nice finish doors or open to custom cabinetry as well see drawings for details and photos of space. Budget is for cabinets to be built and install only bench tbc Must be made and installed to specs and check measurements before installing

Have a deck and want to replace the support beams at the bottom as been in soil for long times it’s about 3.2m height good solid footings.

Hello - we need our deck and stairs stained. Only a small area. I would estimate the top landing is 4m square and then the steps (photo attached). I have the product and equipment. Thanks

Hi there, I'm looking for someone to create a small bed frame for Rav 4 SUV same as pics. You would need to supply materials (Plywood, hinges) but plywood does not need to be as thick as reference pictures. Rough dimensions 70W / 185 L (However split into 3 I have easy parking & sun covered garage with power to work on the build, For a crafty tradesman wouldn't take much time to build. Not looking for perfection, just something solid, level & works with hinge fold down.

To build and install a laundry cabinetry as per the provided design specifications and material requirements. This includes cabinetry installation, shelving, and setup for washer and dryer placement. 1. Laundry Cabinetry Installation: • Install cabinetry as per drawing specifications, with dimensions of 2400mm width by 900mm height (excluding overheads). Cabinet fronts to be constructed or finished with Polytec Melamine in Gossamer White Smooth, matching the updated color sample. Include Sussex door handles as indicated in the design. 2. Benchtop: • Install benchtop across the cabinetry with a 600mm depth to provide a work surface. • Ensure the benchtop can accommodate washer and dryer units positioned underneath. 3. Washer and Dryer Placement: • Provide space and proper setup for stacking or placing side-by-side washer and dryer units as per drawing (dimensions 600mm x 600mm each). • Allow access to plumbing and electrical outlets for the washer and dryer. 4. Overhead Cabinets and Shelving: • Install two overhead cabinets as shown, with dimensions of 900mm width by 600mm height. • Adjustable shelves inside each cabinet to allow for flexible storage. • Ensure overhead cabinets are securely anchored to support storage weight. 5. Adjustable Shelf Installation: • Install two adjustable shelves between the overhead cabinets, as indicated in the design. • Each shelf should align with the cabinetry and provide additional storage above the benchtop area. 6. Laundry Basket Pull-Outs: • Integrate two pull-out laundry baskets into the lower cabinetry for easy access and organization. 7. Additional Materials: • Ensure all materials, fixtures, and finishes are consistent with the design notes, including using Blackened Oak for any timber components. 8. Final Finish and Clean-Up: • Upon completion, ensure all installations are secure and aligned with the design specifications.

Hi, I need two kitchen drawers fronts reconnected to the kitchen draw carcass. Metal drawer sides and joinery front, see photos.

Experienced Carpenter to build out hip rafter to facher finished off so we complete the roofing. as I’m pulling down the chimney and need to extend rafters to lay new tiles and capping. See photos of inside where chimney meets roof currently and outside photos. Ask questions if needed Thanks

I’m looking for someone with the right tools to cut away a large rectangle from the back board of my kitchen cabinets. I’m inspecting the area for signs of mould. You’ll need to make sure your hand tool fits in the cupboard space and that you don’t damage the back wall.

Demolish and dispose of built in timber seat (not deck, just seat/bench). Highlighted in red in one of the photos. I'll keep the 6 best lengths of deck boards as spares, but the rest including structure under bench needs to be disposed of. Cut back bench structure to height of the deck joists. Cut posts of bench back to deck joists. Cut back and grind all bolts back flush to brick wall. Bench to be removed is 2900 long X 450 high X 450 wide I'll reinstate new deck boards where the bench is removed separately. Decking boards are mostly nailed in, some are screwed. Structure is a mixture of nailed and bolted.

Hang 5x upper cabinets, one end panel and hang and adjust 10x predrilled cabinet doors. All materials on site and ready to go 👍

Install shaving cabinet in bathroom - shaving cabinet is fully assembled and is 750mm x 150mm x 720mm. Cabinet to be installed into tiles (with one stud). We have also purchased wall anchors in order to support the cabinet, in case this is needed(?)

Paint step, clean, prep and stain a small backyard deck. Paint supplied - Due date: Before Sunday, 22 October 2023

I am installing wall trim and as the lengths are 3m my carpenter requires an assistant for the day to to help with marking, cutting and fixing frames to the walls. Job is in Annandale Friday 8th December full day 8am to 5pm. - Due date: Needs to be done on Friday, 8 December 2023

I have a large stained glass window that is broken in places. It needs replacement glass pieces. It does not need to be perfect but the holes need to be filled. It is a very old window that cannot be removed. - Due date: Flexible