Find experienced local carpenters in Balgowlah Heights

Remove existing wall shelf system and build new heavy duty garage shelves 3 x 2m shelves. I have attached images of existing wall unit that requires removal and new shelves that require assembly. The new black shelving units will require bolting into cement ground.

I'm seeking a skilled tradesperson with a drop-saw to make precise 45º angle cuts on timber skirting boards. No install required. Details: Material: Raw timber skirting boards Height of skirting: 19cm Number of cuts: Approximately 10 Type of cuts: Internal 45º angle cuts on both ends of each piece Longest piece: 75cm (other pieces vary in length) Location: Balgowlah Heights (work to be done at my home) Equipment: You must provide your own drop-saw Materials: Raw timber skirting board supplied by me Additional Information: Happy to handle the installation and painting myself. The timeframe is flexible, but please indicate your availability. Requirements: Experience with precision woodworking and the use of a drop-saw. Ability to make clean, accurate 45º angle cuts Attention to detail is crucial Please provide a quote for this job and your estimated time to complete the work. If you have any questions or need additional information, feel free to ask.

We have installed new carpet and the doors now have difficulty opening due to the raised height of the carpet! The bedroom internal doors are normal wood doors but the Wardrobe doors appear to be laminate! We need someone to come and do the following; Cut/plane the doors as listed below so they can open without scraping the carpet- 2 X bedrooms have 3 wardrobe doors (5 in total one is working fine ) Then the 3 internal bedroom doors need to be cut!

L shaped cabinets Will need to add cutouts for cooktop and sink. Lower/Base cabinets required Will have to get materials too

The 3 main things to do are: 1- remove coving so new cupboards can go to the ceiling and remove existing cupboard 2- remove top row of tiles 3- make and affix new cupboards and a shelf The main task is making shelves (please see plan attached), so if you are only skilled to do this part and not points 1&2 I can create new tasks for those. It doesn’t need to be anything fancy, just functional. Would be good to visit to measure up and discuss. - Due date: Before Sunday, 8 October 2023

Small part of skirting board to be removed so shelf will fit. - Due date: Needs to be done on Sunday, 15 October 2023

I need someone to help me assemble a plastic garden shed. The shed will be delivered to my place and needs to be assembled under my carport. The shed's dimensions are 2.1 x 2.1 x 2.27m when fully assembled. Please bring own tools. Information under: https://www.bunnings.com.au/lifetime-2-1-x-2-1-x-2-27m-desert-sand-polyethylene-plastic-garden-shed_p3318106 - Due date: Before Thursday, 21 September 2023

Concrete slab and assembly of garden shed - Due date: Before Sunday, 8 October 2023

Build metal shed. ABSCO 3.0x1.52x1.95 - Due date: Needs to be done on Wednesday, 12 July 2023

Portable AC was dirty underneath and after mixing up with the water caused a stain on the carpet- 1m2 - Due date: Flexible

Chisel a table leg so the cross beam fits - Due date: Flexible

We would like built in shelves under staircase taken out.Need builder or cabinetry person to remove them - Due date: Flexible

The cross beam is too large to slot into the table leg and needs to be chiselled. - Due date: Flexible

Looking for a bench seat to be built out of composite wood over an existing retaining wall. Also an outdoor BBQ/kitchen area to be built - site inspection would be required. Ideal to find carpenter who will charge daily rate/has all needed tools and we can pay for any materials needed for the job.

Need a carpenter/ handyman to do a temporary fix on a bed frame to give us a few more months use. Thinking just a plank or two of timber screwed in, from the inside of the frame, where the current frame has snapped will be sufficient. Should be a quick and easy job - Due date: Needs to be done on Tuesday, 1 November 2022

2 x 7m Timber Deck (14 sqm) Deck has been power washed and is ready for sanding. Sand back to raw wood and apply 2 coats of stain. Stain will be provided You will need to supply tools / equipment needed for the job. - Due date: Flexible

We have a bathroom cabinet which was custom made for the space , the wooden housing of the cabinet is still in good shape but all the drawers are now peeling at the front and the base of some of the drawers are water damaged. So basically it would involve custom making the drawers, including the runners and new handles, so that they can fit back into the cabinet. (Have tried to upload photos but it won't work) - Due date: Flexible

Custom dolly needing to be made so a fish tank and cabinet can sit on top. Current dolly needs further improvements to bear the load. Would require you to come look at existing dolly then make a trip to Bunnings and get more plywood/screws etc.

I need a carpenter to cut a few mm off four internal timber doors. - Due date: Flexible

My existing gate has come off its hinges. I need the gate to be screwed in with new screws and fixed into the latch. - Due date: Flexible