Find experienced local carpenters in Bonnie Vale

Need dot rubber laid and glued to a 130 foot square retail space. The strips are 5 x 1m

Hi I’m looking for someone to remove existing timber (liquid nailed on), and replace with VJ groove cladding. The timber joists beneath may need to be changed as the current timber runs vertical. And painted white.

Supply and install marine teak decking boat

I put together a flat pack cupboard. However I need someone to put the doors on it for me. There are 4 of them. There were no pre-cut holes for placement.

Install Easy Shed: 4.5x 2.25 x 2.35 with concrete fixings to existing slab. Plus install 2 Louvre windows. Shed currently in flat packs on site. Must have own tools and experience with Easy Shed or similar. Flexible with time, from Friday 13 Sept

I need one side of old rotted timber gable facia removed to assess total damage and what else may be necessary to replace and repair gable timbers. Initial job is to assess damage and assess what is needed to be done to complete repair. I estimate 2-3 hours max to remove one piece of timber and only assess required time and materials to repair facia. Repair and replacement of east side facia timber is separate new job.

I'm looking at revamping these kitchen cupboards. They're a basic laminate. There's 14 cabinets and 2 drawers. Property is located in Cronulla

We need a carpenter to replace a small timber trellis which has rotted away. The post brackets are already concreted in and good order. Scope of works is install 4 pasts, overhead frame, repaint in white. We will provide materials, only your labour and your own tools in needed. Qualified carpenters only please. Approx 2500 x 1200

We need 2 cm trimmed off one barstool on all four legs as the new one does not match the older ones.

The face panel of the integrated dishwasher is wider than it should be as its side edge is rubbing snug against the bottom of the side panels of the carcass. Hence why the dishwasher has dislodged and is moving, as overtime from rubbing it gave way. I am unsure how to solve the width dimension so it doesn’t rub and I don’t really want a new face panel, but it would be ok to shave the carcass sides maybe?

The timber decking boards are convex and so a mechanical sander won’t work. Majority of the deck just needs to be cleaned before staining but an area of about 3m is exposed to the sun and the previous stain needs to be removed before re-sealing. This will need to be done by hand. I have the stain and am happy to do the full clean but need someone to sand the required area, give it a good sweep and then apply 2 coats of stain, allowing sufficient time between coats to dry.

Need a carpenter or someone handy to build me under floor storage with removable top access, for my canopy I want the floor to sit higher so it has enough room to store things under it but still enough room to have a bed on top I want to be able to access the storage via removing the tiles or something similar. Canopy is roughly 1830: L 1900: W

I have a yardsaver shed from Cheapsheds that needs assembling. The instructions are online and we have a link to them. The shed is similar to the one in the photograph. We’re in Cronulla and available from today until Thursday

Need a carpenter o lobourer to work all next week in cronulla. White card and all PPE. 7am to 3pm. tools no required.

After a flood in the laundry I need to replace 3 cabinets, architrave and skirting board.

I need 3 flatpac underbench cupboards assembled plus bench top cut to fit outside laundry

Turning shed into room gyprocked insulation

I need to cut part of my kitchen bench that is hanging of the end. It is only wood so should be easy to cut and sand the edges.

Our laminate stair noses have come off and need to be glued and nailed in with an invisible nail.

Sliding door is bowed and not used. Need it removed and the top and side reveals covered to form an open doorway The reveal width is 115 wide. Top length is 710mm side length is 2330mm