Find experienced local carpenters in Braddon

We currently have one long cupboard where we store all of our food, split into 4 shelves and a microwave down lower that's a frame built-in, then another drawer below it. We essentially want to put the microwave higher and create better cupboards so that we can see our food and grab whatever we like easily. I'm happy to share pictures and measurements also.

I’ve just had a new fridge delivered and it doesn’t fit through the kitchen entry (space between the edge of the bench and the wall). There is plenty of room in the fridge cabinet space itself. The people who delivered it suggested lying it flat and sliding it through the gap or lifting it over the bench -which I am unable to do.

Build a floating shelf/benchtop 100cm long x 35cm deep - Due date: Flexible

Lower Ikea corner seating. Corner seating made up of 11 draws (screwed together) and a top. We want to lower the draws by around 50mm so the bottom of the draws are finger height from the ground say 25mm chipboard thickness. This will require removal of the existing heigh adjustable legs removed and replacing with a 25mm Moisture resistant chipboard. New 25mm thick chipboard can make up the new Kickboard but will need to be painted black or have a black cover. The two sides of the seating will also need to be trimmed to the new height. Please see photos. Current floor is a concrete slab with veneer flooring. Please ask if you have any questions. - Due date: Flexible

I’m replacing my oven and I need to lower my new oven in existing cabinet by 10mm. Can use existing wood which would need to be cut and then to be the new slats for oven and secured in place. Front of oven cabinet needs to be lowered and sanded. I also have a bench top that has a little wobble that I want secured. Can be done as soon as possible but I’m flexible. - Due date: Flexible

I need a door delivered (within Canberra) and installed. I can arrange a door supplier, but also happy if you prefer to do this. It is an external door on a storage room off a second floor balcony. A standard 2040x820x35 door but needs to be trimmed to 2034x813x35 to fit. - Due date: Before Friday, 27 January 2023

Coat a clear stain on top of 1.2M diameter timber table - Due date: Flexible

Hi - I have a cat door already installed into a piece of Perspex I need it cut to size and a small piece of glass removed from a timber framed door and the Perspex with cat door placed into the timber square frame instead - should be and easy enough job for a carpenter/handyman.

I am looking for someone to build us a dog ramp for two sets of stairs inside and one outside. The inside the stairs are pictured. I have also added some images of what I am looking for. The outdoor stairs are quite small (3 steps) I am looking for someone to build and source all the materials, We would like the ramp to be black, white, charcoal or japan black stain. Please send me a message or leave comments for any questions. - Due date: Flexible

Repair or restore burnt mark left by an iron. Size approx 15cm long, 5 cm wide

DIY resin dining table 180x120 slab on steel legs from bunnings. slab to heavy for legs i think and results in "racking" (wobbling in one direction) would like someone with carpentry experiance to offer sollutions or alternativly fabricate legs/frame that wont wobble and help attach it. After just advice first. - Due date: Flexible

I have an Ikea Eckbacken laminate bench top (246cm x 63.5cm) that I need cut to approximately 240cm x 42cm. The exact dimensions will need to be measured and marked on the bench top. You will also need a circular saw and an appropriate surface on which to cut the laminate.

New office in Braddon, concrete walls (2 walls roughly 7m long). Each wall needs to have skirting boards installed I need someone to: 1. Investigate and decide on appropriate skirting board 2. Organise the purchase of the skirting board (I will cover costs) as well the appropriate nails/screws etc for concrete 3. Install the skirting board - Due date: Needs to be done on Friday, 22nd Oct 2021

Covid permissions allowing - I am after someone to install two powerpoints at either end of my wooden island bench. There is currently power underneath it for the dishwasher, so I am hoping it may not be too hard. Location Braddon.

I need someone to install 2 extra rails in my closet you might also had to add wood panels for the extra rail to be screwed on. The date and the price adjust to fill-in the empty space, feel free to quote and I’m needing it as soon as possible, but not urgent so I won’t be paying urgent fee

3 timber shelving frames need to neatly be shortened by 20cm to make them fit. Will involve unscrewing end boards, sawing 4 struts on each unit and rescrewing end board back on. [ 12 cuts in total ] Timber Struts are approx 1cm deep x 3cm thick. Not a hard job, but does need to be done neatly and accurately.

I have a draw dishwasher that won't fit as the internal panels need to be removed. Willy, if you see this ad, please contact me asap. Unfortunately I haven't been able to get in contact with you.

I have a large melamine cabinet that need to be cut down in height so it can fit in my new apartment. Approx 300mm to be cut off. Then reassembled. Unit is currently empty

im ordering a handi-mate shed from stratco, 2.21 m wide1.55 deep and 1.9 high to install in car park space for unit I own in Braddon, including flooring. Body corporate allows small shed and there are many installed. Concrete floor is flat and dry. It may not be delivered in 2-5 days promised as its xmas

As an isolation project I bought some timber to put together a set of shelves. Unfortunately I feel I probably don't have the tools to complete the job and was seeking someone to complete it for me.