Find experienced local carpenters in Buderim

Double Garage Renovation - remove existing built in shelves - paint floors - install storage systems / wall panels

Recondition pods for rear of boat including cutting out of marine ply to reinforce each pod then fill each with foam aerosol space filler which are then to be fibreglassed over to become water proof.

i need a 2.25 x 2.25 m garden shed installed in Buderim no concrete slab just on grass

I will be having the components of the roof delivered and will need the old roof removed and the new one assembled on fixed in place

Looking at someone with experience to pressure clean and stain my decking, tools and supplies provided. Approx 100 sqm.

Build outside stairs as per photo

I purchased a Mimosa pergola kit. Approximately 3x3.6m. I need it assembled and Dyna bolted into an existing concrete floor outdoors.

35m (roughly) retaining wall needing sanding and staining.

Chat GPT response how to do it! The picture but wider to fit a large case box. Step-by-Step Process: Measure the Space: Measure the height, width, and depth under your bed. Ensure there's enough clearance for the drawer to slide smoothly when pulled out. Plan the Drawer: Based on your measurements, decide the drawer dimensions. Make it slightly smaller than the opening to account for the thickness of the drawer slides. Ensure it’s deep enough to hold the Odysea box comfortably. Build the Drawer Box: Cut the plywood into 4 pieces (sides, front, back) and 1 base. Assemble the pieces by attaching them with screws, using the L-brackets for extra stability at the joints. Make sure the drawer is sturdy and reinforced, as it will hold heavy equipment. Install Drawer Slides: Attach the drawer slides to both the sides of the drawer and the bed frame. Ensure they are mounted straight and level for smooth sliding. Test the fit and sliding mechanism, adjusting if necessary. Install Drawer Under Bed: Position the drawer under the bed and test it by sliding it in and out. The back door of the van should open fully to allow easy access. Add Front Handle or Lock: For convenience, add a handle to the front of the drawer. Consider adding a lock to secure the equipment while driving. By using heavy-duty drawer slides and strong materials, your drawer will hold up to the weight. Price is for labour only Cash! Will buy materials.

Put together garden shed. Easyshed brand 2.25x0.78 flat roof. To be put up on paving already installed.

Skirting boards have been painted and some have been cut, remaining 2 need to be cut and nail gunned onto the walls

VJ feature panels to be installed on lounge wall- white , wood plank width look. Wall is of normal height and in good condition. Does have a power point on it Need someone to measure and pick up boards from Bunnings etc and then install. May get more panels installed in bedrooms at later date if cost reasonable and looks good

Construct part floor and erect new Absco 3m x 2.25m Shed

Small landing on deck needs replacing with hard wood. Approx 6 to 8 planks. Basically it has softened from underground.

Want outdoor deck (size 3m x 5m) built.

Looking for quality craftsperson (builder/carpenter) to take custom design concepts into finished product for outdoor sauna. To source quality cedar (or similar eg Lunawood) for interior and likely clad roof and exterior with Colourbond to match house. Previous sauna build experience preferred.

Have a 1 metre square timber table that needs sanding, staining and a varnish

- build concrete slabs as per shown in pic - 10cm thick required - area about 2x2 m2 - Please quote to include all cost

Basic clean - lounge, main bedroom and 3 small bedrooms. No pest control required. No stains.

We'd like to replace our existing metal pool shed with a new timber one of the same size. The dimensions are 1.5 m wide, 1 m deep & 1.9 m high. The timber shed is to be a mini version of the timber shed in the photo attached, which I recently built. No time to build the pool shed, hence looking for a carpenter to get that done for us. The pool shed has the pool filter and electrics, which will need to go in the new shed. There's an existing concrete slab for the shed to be built on. I have the chamfer boards, corner edging and metal roof.