Find experienced local carpenters in East Melbourne

Need help to sand and refinish dining table. I can provide varnish if needed

I've picked up the oven and replacing with smaller size and need to add a drawer As shown the size of the new oven is smaller than old one so one part of the space need cabinet

Wood trim, windows, around the house Scaffolding would be required for the gutter trim work and would also need to replace flushing. Happy for you to come and view first.

The yellow colour stain on wall under window has not gone away with power wash, May need some cleaning stuff applied and cleaned.

Bleach spilled on wooden floors and needs to be restained. Airtasker must have own staining tools and stain

Need a handyman carpenter to do a workbench. 6m by 0.7m with same length shelve underneath. Quote for supply and install please. See attached pics

Carpenter Needed – Supply & Build 5m x 2m Timber Deck with Stair Installation I am looking for an experienced carpenter to supply materials and construct a 5m x 2m timber deck, approximately 1m high from ground level, with an integrated staircase. The project includes structural framing, decking installation, and stair setup, ensuring compliance with Australian Building Code (BCA) and all relevant regulatory requirements. Project Details: Deck Size: 5m x 2m (10m²), approx. 1m high from ground level Materials to be supplied by the carpenter, including all timber, fixings, joist hangers, bolts, and fasteners Structural Components: Ledger Board (Fixed to Brick Wall): 190mm x 45mm timber, secured with M12 Dyna bolts, spaced 600mm apart Posts (Outside Edge): 100mm x 100mm or 90mm x 90mm H4 structural timber, extending 1m above the decking surface (for future balustrade installation) Bearers: 190mm x 45mm MPG10 H3, Joists: 140mm x 45mm MPG10 H3, installed 450mm apart, sitting on top of the bearers Decking Boards: 90mm x 19mm Merbau, fixed with stainless steel screws Deck Bracing: Decks shall be braced to prevent lateral movement and designed in accordance with the BCA and regulatory requirements Stair Installation: Peak Black 6-Tread Steel Stair Stringer Step Treads: 240mm x 45mm x 1050mm timber Installed as per manufacturer’s instructions Job Requirements: Carpenter must supply all required materials, including timber, fasteners, and fixings Must be a licensed carpenter with experience in timber deck construction Must comply with Australian Building Code (BCA) & Standards Ability to securely install stair stringer and step treads Ensure a clean and professional finish How to Apply: Please provide your quote (including materials & labor), experience details, and availability. Photos of previous decking work are highly preferred. Looking forward to working with a skilled carpenter for this project!

Need to sand back and varnish these two bedside tables so they are more of a chocolate / walnut colour please. Please include cost of the new paint varnish in your quote.

It's a 6 to 8h job, depending on your skills, sanding and painting timber Floor, 2 bedroom and one living room not a big area..I will provide all equipment professional sander from bunnings to make it more easy.

Filling gap in one timber floor board

We need a small kitchen wall cabinet removed above our current fridge to allow space for a new taller fridge. Kitchen Wall Cabinet measures approx W: 105cm H: 48cm D: 35cm and is approx 165cm from the ground It is located next to one other cabinet we’d like to remain there, but they appear to be separately built and stuck side by side. If you can dispose of the cabinet that would be helpful, but we can organise hard rubbish if not Happy to provide further photos, measurements, ideal completion would be prior to Thursday if possible

General carpentry work nothing highly technical - sticking doors x 3, door latches need adjusting x 3, small bathroom door bolts fitting x 2 and window locks fitting to 4 sash windows. Happy to provide more details photos if required. I will supply all materials required.

A friend who was helping me build a cabinet could not finish the job and left me to find someone to do it for me on the last minute! (I know - stressful and unnecessary) All materials are purchased. I have all the measurements and have the info for what needs to go where. It is NOT a flat pack I need someone with carpentry skills. Attention to detail Own tools and to continue this for me ASAP. Any extra info will be provided. I don’t have photos.

Need a Carpenter to do some odd jobs around the house. Including changing some weatherboards one in an awkward position on a patio. Will require support as an hourly rate.

I have two 1200 x 600 mm marine grade plywood sheets. 6mm thickness. I need them cut to 240 x 180mm sized sheets for the purpose of painting. The edges need to be sharp and clean please...!

Please help, I can’t unclip my drawer from Blum laundry unit to be able to plug in new washing machine. Located in Kew. Is there anyone local that could help please?

On our cabinetry we have a pull out cupboard / drawer for our bin. The top strip of the laminate or cover has come off and I need someone to replace it. It’s black. See images.

Resizing the kitchen cabinet to fit in a larger fridge. When I moved in, I had to remove the cabinet on top of the fridge because my fridge is tall. I need help to resize the cabinet (shorter) and install it back to the cupboard.

I'm looking for someone to assist with installing a stainless steel board in a room. The board needs to be 180cm high, and I also require a few holes to be made for the electrical plugs. The picture is the size required, please provide the offer with materials included Requirements: - Installation of a stainless steel board (180cm high) - Drilling of holes for electrical plugs - Please include materials in your offer Budget: $500 Deadline: 31th Oct - 6 Nov If you have experience with this type of installation, please send us a offer including materials.