Find experienced local carpenters in Happy Valley SA

Shed vinyl flooring has come off. I need new vinyl purchased and put in. The bottom of the door catches on the concrete floor, that needs fixing. The door lock/latch needs fixing Shed size 5.25m × 3.15m

Need to change my current kitchen cabinets and install new ones

I’d like someone to come and build a plantar box on site. I have a large piece of roofing sheet metal. Would need the timber. The box needs to be approx 3m long… 45 deep would do…

Need someone with a trailer and power tools to dismantle 27sqm of decking. Only top boards, not the sub frame. Will need trailer, power tools. Approx a days work.

Needing a 3m x 3m garden shed installed, comes in a flat pack just need someone to put it together. Time frame flexible. Someone with experience doing similar jobs preferred.

I need a standard sized dishwasher space created in an existing modern kitchen. there is room for it next to the sink. - Due date: Flexible

Deck is only approx 3m length x 1m wide. Each of the three attached steps are approx 1m wide. - Due date: Flexible

The doors on the built in robes are not easy to open and shut because of worn runners. - Due date: Flexible

Small U-shape kitchen. Existing bench top is laminate and attached via screws from underneath - to be removed. New bench top for installation has 3 pieces. The piece for the left side of the bench is 2500 x 900mm and there are 2 other pieces (both 1860 x 635mm) for the middle and right sides of the new bench top. The 2 x 1860mm pieces will need to be cut to length as well as cut-outs for kitchen sink and stove. - Due date: Flexible

I have a new bar unit I'm putting in and need the sink and dish-drawer plus an icemaker installed. Have run the waterline using 25mm blueline and just need someone to do all the rest as I'm busy with other work on the house. Let me know if you're interested coming to Happy Valley? I have most of the fittings already so would be after labour only rate. Jim

Overhead laundry cabinet installations - Due date: Flexible

Experienced carpenter needed to fit double barn door approx 2.4m width by 2.1m height. All hardware and timber provided. - Due date: Flexible

My pool decking is getting old and is pretty much on its last legs. Need someone to come and install new decking. Must be an experienced carpenter with experience. - Due date: Flexible

A gap has been left above the new oven where a double oven used to be. I'd like an MDF shelf / box built so I can put my microwave in it - Due date: Flexible

Wooden timber gate, just needs to be built a bit higher to stop cat from being able to jump over it. It’s about up to shoulder height at the moment, and just needs a few more built to make it higher And block the side of the shed with a plywood sheet, so the cat can’t go round the side either Unsure on rough $$$ sorry, this would be dependent on materials & time. - Due date: Needs to be done on Tuesday, 7 February 2023

Hi all, I’m looking for someone to design and build a chicken coop in my backyard. Looking for someone who has done this before and can provide photos. Please advise your price on application. Thank you - Due date: Flexible

I had someone attempt to insulate and gyprock my shed that we use as a rumpus room. I have the majority of the materials.so cost.would be mainly for labour.

We currently have a small cupboard door leading to a much larger space under our stairs. I am hoping to remove the entire side off this under-the-stairs area, line it all, and have some shelves fitted into the back - deep enough or some boxes to be added (ideally to kallax measurements for easy box sourcing) but shallow enough for me to add a bench seat in front if I wish, all painted in natural white. - Due date: Before Tuesday, 31 January 2023

Hello I am looking for somebody to make me a total of 6 quidditch goals Essentially it's large Hoola hoops attached to PVC piping of different lengths (I will pay for the materials, on top of the fee for labour) Basic guide below. https://www.wholesalepartysupplies.com/blog/diy-quidditch-goals/

Approx. 3m laminate benchtop installation. Sink template needs to be cut also needs to be cut to fit around support pillars at both ends. Approx. 5m of kickboards to be cut and fitted. - Due date: Before Saturday, 13th Nov 2021