Find experienced local carpenters in Melbourne

I have one cupboard in our office on which I need the old lock removed and a new one installed. I need two keys with the lock.

We brought a semi integrated dishwasher and our kitchen renovation plans have stalled. We need a joiner to add a cover to match the rest of the kitchen joinery.

Remove old integrated fridge and install new one. Ventilation ducts need installing in kicker below and above to allow passive air flow (ie, fans not required). Photos show kicker and cupboard above fridge, which has approx 200mm gap behind it. Grills to be extra at cost, once appropriate ones identified.

Require 2 sets of two pull drawers on runners to be installed - one under a bathroom sink and one under the kitchen sink Also require two floating shelves on top of a cabinet in the pantry. 250mm by 1200mm roughly. Colour and wood to match existing cabinets. Need to visit measure and discuss prior to finalising

We need two joinery panels removed from old drawers and fitted together to create a single panel that can be installed on an integrated dishwasher.

Install a 75inch tv on a joinery wall

Need help repairing several corners of a tv stand where the laminate is peeling Also need help installing cable duct as shown in the photos

Getting some wardrobe joinery installed in bedroom and before it goes in much more, would like to run power behind to service a light switch and a double GPO for desk that is built into unit. Ideally ASAP Have GPO but other materials to be included

Need someone to put together a counter for us. We will be getting the materials pre cut, framing and also plywood. You will need all the tools, saw, drill, to simply put it together. Length 3m Height 92cm Width 1m 3 rows of shelving at back attached rough sketch (note ignore the measurements in sketch and ignore the glass display as that’s no longer needed and specs refer to the specs in this note

Upgrade of a small kitchenette in hair salon, remove some shelving and add a simple worktop bench and add some drawers to an area along with some other shelving. Would love to get opinions on how to maximize space and get you along for a quote. Thank you.

1. Disconnect and salvage existing laundry sink and tapware to allow for benchtop removal (discard offsite). 2. Salvage existing splash-back tiles (if possible) for reinstallation (otherwise replace with matching). 3. Reinstall and connect tapware and sink connection once new benchtop installed (by plumber). 4. Remove left two (2) upper cupboards to allow space for stacked washer/dryer 600mm (W) x 1700mm (H). 5. Supply and install new laminated benchtop, to align with cupboards below, with precut hole for sink, pencil-round front edge. Laminex: Classic Oak Natural Colour Code: 8537. 6. Install/reinstall splashback tiles. 7. Patching/wall repairs using leftover painters paint (supplied). 8. All other works required to complete the tasks listed above. Applicants must include the following or I will not respond to your offer: Qualifications/experience, breakdown cost for each item 1-8 used to establish your offer, availability to commence work, and timing to complete each task. Parking (clearance: 2.1m) available onsite via. 9 Power St, Southbank. Building name: Prima Tower.

Install 3 X corten steel sheets on wall and ply wall paneling joinery.

I need to get painted two piece of joinery with Butterblond (DULUX S13H5),

Remove the laundry cupboard door and help lift a standard sized clothes dryer on top of a washer and reinstall the cupboard door. Due to space limitations the door needs to be removed first before dryer can be placed inside.

Look to custom make a custom retail counter. Specs attached in the photo also reference photos. Looking for a light wood

Need someone to make some drawers out of plywood.

Require a plywood wall joinery

92cm high 180cm depth Length 2.5 m

Kitchen cupboard door has broken. One section has slipped out of another. Needs to be reconnected (glued screwed?).

We are in the process of fitting out a shop in Melbourne CBD - QV centre. We require some joiners/carpenters or handymen to assemble some furniture that has been shipped in from overseas, as well as to put up a few panels to cover some columns and add pegwalls to these. One of our pictures shows units to be assembled highlighted in green, and units to be made up - highlighted in yellow. For the units to be assembled - Generally base cabinets have been shipped who and the shelves on top need to be reassembled. All pieces are marked and all componenets given. Shouldn't be much harder than putting ikea furniture together. For units to be assemled - pretty straight forward - mostly just box out some columns with provided plywood and add some pegwalls from bunnings and frame them nicely. Plywood and accessories provided - except for the pegwalls which will need to be picked up. We are estimating from our past experience that it might be 2-3 days of work for a couple of guys - would prefer to work on hourly basis of approx $80 per man hour. If you work in group of 2 or 3 already that's perfect - otherwise we may hire 2 individual airtaskers to work together. I will also be there to help myself. We have more detailed plans available, however reached upload limit here. Start time Monday 20th or Tuesday 21st - next week.