Find experienced local carpenters in New Farm

Installation of this shed: https://www.stratco.com.au/au/sheds--garages/garden-sheds/stubbie-sheds/stubbie-roller-door-shed-slate-grey-ghshty1srdsg/ Must have experience. The ground is currently half concrete and half dirt.

Sheet this wall with ply, ready to hang overhead cabinets. Single thick asbestos wall with timber frame to screw into. Needs ti be cut out around GPO. Supply and install required.

We would like a floating bench installed into our concrete wall - we want it to be edge to edge and weatherproof as it will be situated on the balcony Dimensions - 180cm L x 50cm D

We would like VJ panelling installed to act as a bedhead. Dado rail installed on top to finish it all off. Photo 1 - current bedroom Photo 2 - inspiration Supply & install Measurements of VJ required: 3.3m wide 1.1M high

Install stone kitchen benchtop - 2 pieces One piece needs the hole for the stovetop cut The complication is that on the side of the stove, the bench needs to be raised about 20mm so it will be level. Also looking for someone to remove the old benchtop.

4 shelves to be built from materials provided, It’s a tiny room under a stair well that I use to store tools and bits and bobs. I have some old vj’s that I want to use as the shelf, and some timber rails that were left over from previous jobs, The job may take an hour or two, no longer, The shelves will take 3 x vj’s per shelf so may need to be secured, maybe screw down onto the timber support. Open to suggestions when you see the job. Also have a small plastering job about 1 foot square, where a hole has been half fixed, would be good if you can do both.

Wanting to do a small makeover of my existing kitchen. Wanting to replace the kitchen doors and drawers with something more modern and update the kick board. The layout and size of the exciting kitchen is perfect, was only done a few years ago. Just wanting to update the doors and kick board Measurements below Island Bench - 9 drawer fronts: 98cm (W) x 24cm (H) Main Kitchen Area - 6 door fronts: 40cm (W) x 74cm (H) - 1 integrated dishwasher door: 60cm (W) x 74cm (H) - 1 door front: 15.5cm (W) x 74cm (H) Above Fridge - 3 door fronts: 38cm (W) x 31cm (H)

I need a QBCC-licensed carpenter, cabinetmaker or joiner to do a 16mm MDF kicker/baseboard under already-installed media cabinetry (pictured; approx 3325mm long, 315mm deep). This is to provide a suitable substrate for another trade to provide the finish. Best to visit site to measure up before making. Flexible with budget for reasonable adjustments.

The location is a courtyard with an alcove large enough to fit the 2.25 x 0.78x 1.82 shed. The floor of the courtyard is concrete with an epoxy coating. The ground has an uneven fall between 18mm and 22 mm, so the shed will need packing to stand straight and sealing to be waterproof. PDF Instruction Manual at https://www.manualslib.com/manual/3406002/Easyshed-Ef-S2308.html The manual says two people are required to install and I'd prefer a tasker with experience installing sheds. The budget on the next page is for installation labour. I'll pay for all materials.

2 PAX wardrobes Queenslander home, will need fixing to walls with some variation due to skirting boards, floors not 100% flat,

Please ignore budget, i just need quotes. I have 2 areas in my property with obvious scratches to the timber floor. One is more surface level, the other has a slightly deeper gouge and ripple to the floor. I am just looking for quotes in preparation of a possible move to see if it's cheaper to repair or lose my bond. Happy for someone to attend the unit to give a proper quote if they are unsure. Areas are both at least 1m square i recon.

Need help cutting off a rounded edge of a bench-top. Just chipboard. I don't have the tools. Probably a 5 minute job.

Need a quote for work on my townhouse. I will pay for you to provide the quote. I need the quote as requirement for body corporate approval for the work. You must be a qualified builder or carpenter. Work for which quote is required: 1. Dismantle and make good lean-to verandah about 2.5m x 2.5m and 3 brick pillars supporting verandah 2. Install wood sliding doors replacing current alumininium bi fold doors 3. Repace wood front door with wood framed glass door.

Hi, looking for a builder to provide a cost guide to build a built-in bookcase in a bedroom

Looking for someone to supply and install a clothing rail in our wardrobe. Currently need a second rung to be run along the existing infrastructure for about 2m - might need to be installed and supports off the ground. Happy to send photos. Please allow for materials on quote.

Looking to raise the house and extend the back and build in underneath so I need to know the boundaries and height to see how much we can raise it.

I need a garden shed built please from a flat pack. Likely to require two people. I have a newborn and a toddler and won’t be able to assist you with building it. The shed is called YardStore F52-S - 1.76mW x 0.72mD x 1.8mH. See web listing here for photos and details: https://www.australiangardensheds.com.au/product-page/yardstore-f52-s-colorbond-1-76mw-x-0-72md-x-1-8mh After someone who can build it on Monday 13 May in New Farm.

BBQ kitchenette installed on small apartment balcony We’d ideally like to have a stainless steel benchtop with a nook to store the BBQ & space for a bar fridge Photos attached which shows current layout & inspiration that we’re going for Measurements are 1.8m wide x 0.55m deep off the wall

The IKEA METOD pantry and fridge cabinets were installed by ourselves and need help in putting the fridge and vents on the Plinth, and to flush the both pantry and fridge cabinet doors. Some shelf’s to be put inside the cabinet as well( comes from IKEA) https://www.ikea.com/au/en/p/superkall-fridge-freezer-no-frost-white-integrated-20509016/

We would like a portable ultrasound table that allows us a place to arrange cables, hold probes, and ideally, would be collapsible to save space in transport. Like the ones in the photos. It may be easy to adapt an existing cart.