Find experienced local carpenters in Northcote

Install 7 spigots into decking Then insert glass panels(7) into spigots Materials all supplied

Someone with experience in making/building cabinetry to assist in choosing and installing shelving options in kitchen/laundry and garage.

Recent carpet installation, now 2 sliding wardrobe doors need to be trimmed by approximately 5 mm and then hung onto railing that is already installed. Installation is simple, however doors are heavy and one person will be made available to help move and carry them as needed.

We are building a living room wall Bookshelf/cupboard unit using a combination of ikea carcasses (METOD) and then custom cupboard doors, cover panels and open shelving units etc. Here is the design link below which was built using the Ikea planner; https://kitchen.planner.ikea.com/au/en/planner/?projectId=E41629C6-BD29-49A9-93F8-220509F8C331&ref=share All lower cabinets to be offset from wall by installer by approx. 110mm to allow for around 500mm depth to cabinetry. Top panel on cabinetry will hide void behind. -Raw panels – our 18mm thick Raw panels are unfinished on one side, with a white melamine backing to the reverse. Both sides can be easily painted, however we do recommend a laminate primer for the melamine face to ensure paint adhesion. - Oversizing – in most cases, panels have been oversized slightly to allow for any variation on site. - Benchtop and top horizontal capping – these have been supplied in 3 sections. We suggest that joins be located at the break between cabinets 7 & 8, and 11 & 12. - Base cabinet depth - the shallow base cabinets will be offset from the wall. We have allowed for the right side cover panel and benchtop panels to be a maximum depth of 600mm. Once the preferred depth is decided, these can be trimmed on site. - Shelving depth – we’ve included panels for shelving at 350mm deep. With an 18mm thick backing panel attached, the overall depth would come to a maximum of 368mm. Happy to amend if you would prefer this to be deeper. - Vertical gables - vertical members (excluding the far right and left gables) have been included in double thickness to ensure adequate support for shelving and ease of installation. - Backing panels – these have been included in sections. We anticipate your installer would construct the open shelving as modular ‘boxes’, with the top capping panels installed above once the boxes are fixed.

Hi, I need an existing three door wardrobe removed, including the shelf and rail inside, along with the wall it is built into. I also need the skirting and cornice removed for that section as built in robes will be going there

Replace existing decking on balcony Repair and and or replace bullnose timbers Secure existing timber frame

I have two widths of ply-wood They need to be cut-down to 2000mmH so I can clad some joinery. Note: able to come to you, if you have the equipment set-up!

We have a cabinet which we wish to use a shoe cabinet, only it’s too deep for the spot we want to put it. We need someone to take apart the cabinet, cut the plywood to the new size and reassemble it back together.

Supply and install 2 matching timber vanity doors to existing vanity

Had started assembling flat pack bunnings kitchen then got sick. Need to finish off cabinets and mount to walls for benchtop and fit off. The house is off St georges rd, Northcote. Some cuts will need to be made to the panels to fit, as mentioned in some of the plans Other potential handyman odd jobs available and rate could be negotiable for day +

Need the back deck cleaned and stained. There is an external office with wood panels that will also need the same work done. The decking may need some minor repairs (nailed down again for loose boards). There is an outside storage shelves and sink that will need to have the items removed to clean and stain this area as well. It’s approx 40m2 for the deck and much smaller for be office. Airtasker will need to bring equipment and materials.

The slide on one side of a large wardrobe drawer doesn’t allow the drawer to open completely and may need repair/ replacement

Reconfigure a free standing L-shaped nib wall in living area to make it straight and extend it towards the actual wall

Installation of Natural Walnut Acoustic Slat Wood Wall Panels from the wood veneer hub. Requires installing slats behind and cutting panels to size and drilling in.

Hi, We have the 3m by 2.25m gable roof Easy shed with a sliding door. It’s currently half installed but we need someone to come to finish the job and connect it to the concrete slab using the supplied concrete fixings.

Adapt exisiting built in shelf area to create a desk , and adapt how doors close to make them ‘pivot’ and close internally , plus remove a couple of built in shelves

Looking for shelves made and installed in a wall cavity. Measurements of the cavity is approximately 2600mm (H) 890 (W) 470 (D). 3 to 5 shelves depending on recommendations

Current deck is approx 3600mm x 2800mm. I require the 2800mm to be ‘extended’ in order to fit a 3mx3m pre made pergola onto it. To total deck to at least 3100mm x 3100mm I will attach photos. Of deck being built and the finished deck for reference Would require the artificial turf to be stripped back a bit and a couple of rocks moved

Make custom pantry and range hood cupboard, door for sink cavity and kickboard for kitchen

I need a small rectangle dining table made to fit my kitchen dining area. Standard tables are too long or too wide. The dimensions for the proposed table are approximately 1250mm Length, 750mm Wide and 770mm High. I'd like a timber or laminate top. The legs can be timber or metal, positioned at each corner of the table to give room for the chairs to fit. The design needs to accommodate 4 dining chairs in a configuration of pairs on both sides, not one chair per side. I'm looking for a very modern style, not a chunky farm house style. See image. I'd take advice from you about the final design and type of timber. I recognise that a firm quote isn't possible until the design and materials are chosen. So a quote for making the table plus materials is probably the way to go. I've posted $800 to make the table. I'll cover the cost of materials separately.