Find experienced local carpenters in Pymble

Trim a hardwood desk top. Would like it trimmed down to 160cm, it is 26mm thick

Description: We need a skilled handyman to create a concrete ramp for our storage area (Orange part on the photos). The ramp will provide easier access for wheeled equipment and vehicles. The finish should be smooth and durable for regular use. Key Requirements: Experience in concreting and ramp construction. Ability to provide materials or a quote for materials. Must adhere to safety standards and ensure the ramp is stable and functional. Must have necessary tools and equipment to complete the job. Location: Pymble, NSW Job Type: One-off task Please send through your quotes, availability, and any previous examples of similar work you’ve done. Looking forward to hearing from you!

I have an awning frame attached to house. It's 3000*1000. See photos. I'd like a polycarbonate panel fitted to the top. 3000mm length, and ideally approx 1200mm width, so it overhangs the frame slightly.

I want someone to make a timber shoe rack for outdoors with the below dimensions (3 levels/shelves to maximise # of shoes it holds), so bottom shelf would be at or near the floor. This will get wet with heavy rains, please tell me what timber you will use in quote Length = 1115mm width = 290mm height of each spacing between shelves ~160mm I have added a sketch and photo of location

I have an outside table & bench seats that has steel frame that all the wood needs to be replaced . All wood needs to be supplied

Looking to install a new custom wooden door for our kitchen. We need an experienced carpenter or door specialist who can create and install a durable, high-quality wooden door to suit our space. Requirements: Strong experience with custom woodwork Familiarity with commercial kitchen requirements Ability to measure, design, and install to fit precise specifications Measurements: Wide 70 cm Long 152 cm Cheers

Cut, prime and glue in place mdf board for fire place infill, ready for painting

Relocate built in wardrobe from master (A)room to 2nd room (B) (same dimensions for both and frame on both units to be kept) Basically removing sliding door and internal carcass of wardrobe in bedroom A and installing in bedroom 2 (B). Refer to photos.

Looking for someone to source timber and replace one piece of damage timber per attached photo, I can reimburse for the timber piece

Install 3 internal doors, including 2 doors may need to trim 5mm on width and 10-20mm on height.

Hi. I need a Easyshed Bike Shed put together. https://easyshed.com.au/products/garden-bike-shed-2-25m-w-x-0-78m-d-classic Just the shed straight on to the ground (No base).

1. Remove the wood wardrobe measuring 2.6 hx1.7w meters. 2. Repair the floor underneath to match the surrounding timber flooring. I provide timbers. 3. Amend 1 hole （ estimate 20cm）on the ceiling

Cut and install kitchen benchtop board - Due date: Before Tuesday, 12 March 2024

We are seeking a skilled stone mason who can come to our residence in Pymble and expand the existing cut-out on our current Corian countertop to accommodate our new cooktop. - Due date: Needs to be done on Friday, 1 December 2023

Hi, I’m after a base for bar height bench 3120x780x40 and installed by next week at pymble area. Will need the side cabinets 200-300 x2 with hinges door and wine storage 400 in the middle to support the stone bench. Draft plan attached without the side cabinet but flexible with ideas and design. Skirting is about 115 so will need the kick board to avoid cutting the skirting. - Due date: Needs to be done on Wednesday, 15 November 2023

Hi I have two in built wardrobes and I would like to create more Shelves - Due date: Before Sunday, 10 December 2023

reassembling retail shelves in st ives

unassembling retail shelves and trimming top of shelves by 1meter - Due date: Needs to be done on Thursday, 26 October 2023

I m looking ir a carpenter who can install the wooden slats like a privacy screen added n the picture. I m using Dressed all round timber and the width is 140cm so maybe around 10 to 12 slats to install - Due date: Flexible

We need a custom flyscreen made up for two doors in our house. Approx 0.8m x 3m, Would want something simple that can just be slot in or taken out (no need for rollers etc) Keen to understand the estimated cost to compare against solutions like magnetic flyscreen or refillable mosquito repellers etc - Due date: Flexible