Find experienced local carpenters in Ryde

Office renovation: A new floating desk, wall to wall Drawers Floating shelves and enclosed bookshelves LED lighting Attached a plan sketch. All measurements in cm

40 yr old large solid robe. Door operates on pivot hinge now rusted out. Need to hinge differently. I believe this is possible but tricky.

Need to join panels on a dishwasher that is embedded in kitchen cabinet

Joiner to make custom designed laminated workbench /benchtop from 32 mm thick MDF for home office. 330 cm long, 85 cm depth, supported with 40 cm wide, 50 cm deep chest of drawers on either sides and shallow drawers (under the benchtop) in the middle, supply and install

I have an ikea office wall cabinet (1200mm x 1280mm) that I need to be removed and cut down to reduce width ( 1200mm x 700mm) and the wooden bench below reduced from 1500mm to 1000mm. This is required to make room for a new fridge/safe ( 1800mm x 500mm). I’ll be free to assist on the day if an extra set of hands are required.

We want to get quotes for joinery and new kitchens for our upcoming new house project, we need someone good with CAD that can come out to site and we show them where we want what cabinets to be etc so you can put them on a set of plans with measurements etc so we can use it for quotation purposes

Hoping someone with joinery skills would be able to make a desk like the one in the link. I would need 2, and both around 1 metre wide. These do not need to be beautiful. Essentially a strong box with hinged lid attached to the wall.

We recently installed new joinery and need a gyprocker to box up the space between the joinery to the ceiling and for two rooms we also need a side wall/lined as well Looking for square set finish: Space in kitchen: Space above stone top: 232cm wide x 49cm high x 35cm deep Small cabinet before window: 57cm wide x 49cm high x 35cm deep Space above fridge: 130cm wide x 49cm high x 35cm deep Space in butlers pantry: 245cm wide x 49cm tall x 35cm deep Space above built in bookshelves: 306cm wide x 35cm high x 35cm deep Space above built in number 1: 200cm high x 35cm high x 60cm deep Plus a gyprocked wall on the side that is 275cm x 60cm Space above built in number 2: 100cm high x 35cm high x 60cm deep Plus a gyprocked wall on the side that is 275cm x 60cm Big built in number 3 is L shape and has a traditional curved cornice One side is 362cm width x 10cm high x 60cm deep The other side in two sections: First section: 211cm width x 10cm high x 60cm deep Second section: 102cm wide x 10 high x 60cm deep Looking for a square set finish to be sand and ready to paint. Must include all materials Flexible on timing.

Need an experienced joiner or joinery apprentice to do a range of tasks for a full day. Installing some skirting boards, installing quad trim, installing some cornice, re-hanging a door that’s has not been hung right and doesn’t fit. A full day is 8 hours of work. The work doesn’t have to be all done on the same day. A few hours could be done on Friday and the rest on Saturday for example.

I require 1 ikea metod 4 drawer assembled and installed, 2 metod wall cabinets (no door) and 2 bench tops and side panels cut to size and installed. One of those Benchtops will require a sink cutout so the old sink can be used. I will require the old joinery dismantled and discarded. Existing joinery consists of 2 drawer units, bench top, 3 sets of shelves and one metal display unit. Photo 1. Ikea design Photo 2. Ikea order form Photo 3. Existing joinery which needs to be removed (all stock will be removed for quick demolition) Photo 4/5 This is the existing sink and existing base unit which holds plumbing and hot water system which I will keep and will not need to be removed. I plan to replace the benchtop on this section. This is a commercial premises and can be accessed on Saturday from 12pm -9pm Saturday or Sunday 7am to 3pm. I would ideally like it all complete in one day if possible. - Due date: Before Sunday, October 2, 2022

Remove and discard old laminate kitchen bench and shelf - Due date: Needs to be done on Saturday, October 1, 2022

You will need to have experience and the required software as I need site measure and drawing of the following joinery: Kitchen joinery Underneath staircase joinery Laundry Joinery Linen Joinery BBQ area joinery Walk in robe joinery There is a requirement for a site measure (the house is under construction but the drywall is already on) and drawing. The site measure should take roughly about 15 minutes to do as this is a duplex (you are only measuring one of the houses). I will require the drawings to show the following: 2d and 3d of the joinery in each area (i.e. kitchen separate from staircase, from laundry and so on) The drawings in some areas such as the panty need to show the shelves inside. The drawings need to have a front and top view. preferably all in 3d but front could be 2d and top 3d. They need to be in pdf format with each area noted above shown as different items (rather than one big document showing everything). Color is not required, I have attached some samples to this request however I will need a bit more details and also the measurements shown against the drawers height width and debth - Due date: Needs to be done on Wednesday, 23 March 2022

Custom-built display cabinet for beauty salon. Timber construction with glass shelves. Plan available. Provided with or without LED strip lighting. - Due date: Before Friday, 8 April 2022

I’m after someone ASAP to move a wall unit and kitchen cupboard from the garage to inside the house. The wall unit is pre-made and will have to be joined inside. When constructed it is approximately 2.5x2.2m high and the material is spray painted mdf. It consists of 4 parts that need to be joined together and anchored to the wall. The kitchen cupboard is about 1.2x2m high and is also pre-made. To get from the garage to the house is a sloping walk way and a trolley will need to be brought (if you don’t have one let me know and I can bring one) to transport the parts to the house for reassembly.

I imported so backdrops that incurred minor damage during import. The backdrops are a combination of sized, but are heavy as they are made of wood. Job can be completed anytime, just need back by August if possible. Damage needs to be cut away, bogged, prepared and sanded. I would like to paint the pack drops a different shade of the same colours so no need to match perfectly. I will have to pick the colours for you. Please quote including pickup, works, timing and return. Proven experience is required.

I have 4 basic tasks needed for my kitchen. NOTE: colour of kitchen cabinetry etc is SATURN POLY 1. REFER TO PHOTO WITH FRIDGE AND ARROW. I need finishing panel 700mm wide where arrow is pointing 2. REFER TO PHOTO WITH 2 HANDLE CLOSET Currently the doors are a little too wide causing paint to scratch. 3. REFER TO PHOTO OF BOTTOM DRAWER WITH SCRATCH I need the scratch mark fixed 4. REFER TO NARROW STORAGE DRAWER DOOR it’s a little too big hard to close

We are looking to do 2 x small and shallow cabinet (25cm depth 88cm wide) with 2 floating shelves on top. Similar photo attached below. Can negotiate price