Find experienced local carpenters in Templestowe Lower

Demolishing an interior partition wall and moving the room door

A commercial property requires the replacement of a kitchenette with sink and cabinets above. Discuss a new small partitioning wall at the time.

I'm looking for someone to assist with installing a stainless steel board in a room. The board needs to be 180cm high, and I also require a few holes to be made for the electrical plugs. The picture is the size required, please provide the offer with materials included Requirements: - Installation of a stainless steel board (180cm high) - Drilling of holes for electrical plugs - Please include materials in your offer Budget: $500 Deadline: 31th Oct - 6 Nov If you have experience with this type of installation, please send us a offer including materials.

Hi, I need a custom vanity cabinet built to fit within a maximum width of 560mm. I already have the stone top and faucet, so I just require a freestanding, two door semi-glass cabinet with the following dimensions: • Width: 560mm • Depth: 600mm Please let me know if you’re able to help!

I am looking for a cabinet maker that can assist me in making my tv unit. 2.4m floating unit at bottom and shelving unit on one side. Cladding and sheets to be installed to rest of unit. Also cladding of meals table and one side of island bench. For cost , let’s discuss to see how you can assist and agree on materials and finish etc and you can then quote me. I will just put the min $5 for this ad.

Build out a cavity in a wall for a fireplace, then plaster the wall and paint Area is approximately 1800mm x 230mm high

Install hettich wing 77 bifold system for laundry doors. One 4 door set and one 2 door set on one (6 doors total) track 2730mm wide. Top track installed on timber beam. Bottom to custom affix to tile floor. Bottom track may need to be packed as floor is not level. Panels are to be Ikea askersund or similar. Hettich system already bought. Ikea panels I will buy unless you are able to supply something similar. Old house so some variation https://shop.hettich.com/au_EN/Folding-door-systems/Folding-door-system-Wing-77/c/group743682361007

Take off the panel underneath the oven, shave 5-10mm off and install it back

We would like to build a timber divider as the photo. The size is around 2700mm high x 250mm wide x 1000mm length. It will be from floor to ceiling. Not sure what timber to be used.

Need handyman carpenter to install decking around 20 to 25 sqm outside flour area and retaining wall Labour only timber i will provide rest instalation and nails cement etc you will do

Need experienced cabinet maker to cut and install a laundry U-shape laminate particle board benchtop with sink cut out. See photos. Uncut egger benchtop on site has a bullnose edge. Must have own tools. - Due date: Before Friday, 26 January 2024

I need to extend the space in terms of height and width for my new fridge to fit in . Almost 200 mm width and 200 mm height. - Due date: Flexible

I need a wood box made up to store a flat mat. 80 X 80 cm Height = 15cm It needs a hole so I can put a lock on it. - Due date: Before Tuesday, 19 December 2023

Hi there, Require new doors to be put on wardrobe - Due date: Flexible

Outdoor steps to the back door, wooden railing needs replacing. The posts/supports are fine but the railing is rotten. - Due date: Flexible

I have 3 timber decks that need to be sanded and restained. Front entrance, backyard, top of the back yard and steps to the top of the backyard. All timber decks are in good conditions, but need to be rejuvenated. - Due date: Flexible

Kitchen cabinet installation, planned and purchase from IKEA. - Due date: Needs to be done on Saturday, 12 August 2023

Increasing the size of the fridge cabinet and build a pantry - Due date: Flexible

I need someone to install 3-4 base kaboodle bunnings cabinets, bechtop, and sink. The design is attached. - Due date: Flexible

We have a solid Timber table and chairs that need to be completely sanded back and recoated. There is a garage where work can be completed by person will need to bring all tools. - Due date: Needs to be done on Saturday, 6 May 2023