Find experienced local carpenters in Wadalba

Need a shed built asap Details in the photo

Put together a dog kennel

Window frame replacement and kitchen bench framing replacement.

Need a small garden bed fenced off which is attached to a deck with already purchased puppy proof wire. Also using the same material fencing off a roughly 2 metre wide side access. Need to have experience in this sort of project. Small job.

Kitchen window sink , window timber has some sort of wood decay, below the glass. Or wood has rot. Not sure if the whole wood piece needs to be replaced would also need the windwow changed too. - Due date: Before Friday, 8 March 2024

Need to install a Cefito pull out bin into a kitchen cabinet. Needs to put 4 additional holes so the wood can be lowered down. Need also to secure the board and - Due date: Flexible

Install Easyshed on existing concrete pad 3mx1.5mx2.1m and bolt it to concrete. Shed and fittings on site and ready to be installed - Due date: Flexible

Brand new small backyard garden shed needs to be put together. will come with instructions

Rectangular frames with joins or screws at the corners This is not a complex task, it just requires the correct dimensions Dimensions: frame 78cm wide at outside edge of frame This is the size inside the window frame 15cm deep (width of the wood) This is the depth of the window sill 42.5cm high at inside edge of wood This is the height to fit the fan Same x 2 for two matching frames To also purchase/cut two long flat pieces of wood One for each frame ~60-70cm by 8cm deep by 3cm high Could also use 2x short pieces eg 20 X 8 x 3 (four total) This is to sit on the window sill under the frame so it sits level (it could be attached to the front edge of the bottom of the frame or it can be left loose) Please adjust your offer to include the price of the wood Optional extension: To fix the fans into the frames To cut and fix perspex to go either side of the fan To start on task allocation and complete by the following day Task execution needs to be efficient, steady, no fuss Drop off by prior arrangement and confirmation the hour before, with SMS on arrival

The top of the table needs to be adjusted so that it is level It is made up of panels and attaches to the wooden leg underneath That is all that needs to be fixed, to make the top level I would like someone with carpentry or furniture repair experience who is able to problem solve, communicate potential solutions before implementing, then fix it It may need to be taken apart, or underneath might be able to adjusted to make the top level. I do not have better photos or more information at this point. I do not want someone to come and look at it first. I just want it to be picked up and taken to a workshop or whatever, and that once it is there, communication to figure out how to fix it. If it can't be done I will pay partial task, if the process is extended the task price can be negotiated. Pickup preferred Please comment with your offer if you can pick up If you need it dropped off please comment your location and when you will be available to receive it with your offer I would like this to be completed this week With photos sent on completion I would like you to hold onto it until I am ready to organise pickup either later this week or next week Tia

Erect a flat pack garden shed 3m x 1.5 x 1.8 freestanding can help if needed - Due date: Flexible

Hi Looking for a carpenter or a handyman to make a deck for us Need to come out and give us a quote Located in wadalba central coast Budget i put below is for the sake of having one. We can negotiate after the quote Measurements of the area is below in the attached image Due date: Needs to be done on Thursday, 15 August 2022

4.2 x 1.75 x 2 shed (may need offsider for an hour or so) Most of the sides assembled Concrete base already there

Deck on ground level recently re-done, requires oil/stain...need quotes. About 25-30sq m. Would like 3 coates applied

Need help setting out and cutting 140mm merbau decking and screw boards down. Have all materials but need experience and own tools.

Needs to be a flat wooden sheet of wood to use as bedhead Sheet of wooden 107cm wide x ~20cm high (height tbc) Two clamps (attached to one side of the wood?) facing down with a possible grip width starting at 3-4+cm to finish at 2.5cm when closed Clamps spaced 99-100cm apart Clamp width 3cm or less Clamp depth ~5-10cm Wood thickness needs to be solid 2-4cm Sanded for rounded corners and smooth finish, low VOC finish for reasonable waterproof (needs to be wipeable), aired Type of wood is negotiable. Not too heavy, soft is ok, light coloured is fine Task requirements Work from these specifications This information should be sufficient to move forward with task allocation Send diagrams and progress photos to confirm specifications are understood Send photos of wood thickness and type prior to purchase or prior to cutting if already in possession Send photos of clamps prior to purchase or prior to attaching if already in possession Please comment when you expect to begin and complete the task with your offer Delivery will need to be preorganised once task is completed, to occur at a specific time

Refer to attached sketch ~ sanded smooth finish, slightly but not excessively rounded corners ~ optional- if varnishing to make it waterproof. Needs to be very low VOC (special products) ~ bottom piece of wood to be thick and heavy to weight it, needs to be managable weight for one person to move it though; approx weight 5-6.5kg or so, need to confirm the finished weight of the wood prior to beginning construction ~ four pole pieces need to be primarily attached to the outside, not as internal poles. Can be thicker width wood at the ends than the front. Confirm suggested width. ~ needs to use screws not glue ~ needs to have a lip on the top and bottom pieces of wood Dimensions 60w x 45d x28h In cm; internal dimensions Other widths of wood negotiable- please confirm Lips (in purple) Top ~5cm high Bottom ~5-10cm high Within a week completion would be good; send progress photos by sms to confirm; ~ arranged delivery time beforehand and confirmed on the day by sms ~ drop off to wadalba, exact time confirmed prior, needs to be late evening/overnight/early AM Price of materials inclusive in task price Note: there are no existing images of what the design looks like, design needs to be based off the sketch not the image Note: a tasker was previously allocated to this task but is not replying, this task will be allocated in lieu of that one if not completed

Shed has already been purchased. It will need a small concrete footing. I can supply the concrete, but I’ll need your advice about how much and if rapid set is fine to use.