Find experienced local carpenters in Williams Landing

Hello! I am looking at installing a Stratco garden shed I purchased - it's about 2.2m wide, 1.44m deep and 1.9m in height. it'll have to be in a part of the backyard which isn't currently concreted. There were 2 trees in the photo which has since been cut down (without stump removal). Shed - https://www.stratco.com.au/au/sheds--garages/garden-sheds/handi-mate-garden-sheds/handi-mate-hinged-door/handi-mate-hinged-door-shed-hm4-merino-shmshsdhm4me/ Thanks, Waseqa!

One Window of first floor needs staining after sanding properly.

Install a shed in concrete- https://www.bunnings.com.au/build-a-shed-1-2-x-2-3-x-2-0m-skillion-single-hinged-side-door-shed-grey_p0378283

Need to change few of the draws on my kitchen. May be a new laminate.

Hi looking for someone to make me some shelves for this cupboard. I’d like shelving all the way down

Good Day, I would like a handyman to come and install 3 x folding doors into our home. Basically the bedroom ensuite have these exact same doors from Bunnings installed but they are getting old and broken so just need the same one's removed and new one's installed. I have already taken measurements today and there are 3 doors upstairs and 1 door install downstairs measurements below. The matching door URL for bunnings also entered below: (lengths in cm) a) Upstairs x 2 door installs (all identical in dimensions) 77 w x 21 d x 206 h https://www.bunnings.com.au/pillar-85-x-203cm-white-platinum-pvc-concertina-door_p2036926 b) Downstairs x 1 door installs 12 d x 237 h x 82 w https://www.bunnings.com.au/pillar-85-x-203cm-white-oak-san-marino-pvc-concertina-door_p2036924 Person needs to pickup the items from Bunnings Hoppers Crossing and take it to Williams landing vic 3027 and install into the house. Job would ideally be done within this weekend or within a week.

Sanding and staining of the balcony facade, balcony door, front door and windows (see photos will green areas highlighted that need work) Stain will be provided. Will need someone to do the job tomorrow (Wednesday) or Thursday.

I have an alfresco that was built with with the house. I want to extend or build an additional space to convert it into a room maybe. I would prefer to use colorbond walls with fire rated material. I would also like the get the approval for it included.

Take off Ekodeck decking panels neatly (the panel must not be damaged as it will need to be reattached).

Replace floor trim - I have the trim but need it installed. It is just one piece which has lifted where the hallway meets the living room. The piece will need to be cut to size and installed. I will need an invoice and warranty as per the landlords requirements. If you are able to complete this task, I look forward to chatting to you! Cheers! - Due date: Needs to be done on Tuesday, 16 January 2024

Please refer photos for the requirement. Due date: Flexible Price: Negotiable - Due date: Flexible

Looking for a chippy to help put up our feature wall in the living room. (3.5X2.7 )I will supply the wood which I already bought. You’ll probably need 6 tubes of liquid nails an air nail gun and an electric saw of some sort. I will have the wallpaper removed from the wall before you start the job. Also the current skirt needs to be removed and a new one that’s little bit higher glued on to the bottom. https://www.bunnings.com.au/80-x-19mm-2-4m-ascent-kd-tas-oak-prime-grade-lining_p0342926 There are 46 pieces of wood in total - Due date: Flexible

Planter box (cumaru) ~250cm x 35cm Deck (cumaru) ~350cm x 300cm Would like to get deck cleaned and restained/oiled Please supply all equipment and stains - Due date: Flexible

I have an easy shed to be assembled. There are also some fibreglass skylight panels as well that will need to be cut to the same height of the roof panels too. - Roof: Skillion roof - Shed size: 1.5m x 3m - Anchored into concrete (I have the anchors) Here is the shed: https://easyshed.com.au/products/skillion-roof-garden-shed-1-5m-w-x-3m-d-classic?variant=44453503074463

Kitchen bench top has been cut inaccurately by previous owner to fit 900mm stove top which has left an inch gap between the stove. Looking for someone to measure, provide and attach a fill in piece of artificial stone to cover up this mess - Due date: Before Sunday, 26 November 2023

I am looking to convert my front balcony from timber to glass panel. A carpenter will do the cutting (separate task). I am looking for a roof plumber to give a quote on flashing before the glass panels are installed. Tentative date - Oct last week or early Nov - Due date: Flexible

I want to get some overhead cabinets (either custom made or buy something from ikea or bunnings) put in on the 2 side walls of my garage. They should run from about midway towards the ceiling so I can open the car doors and have the extra space. Budget is roughly what i thought it might cost, slightly flexible See attached image as a rough measurement. I realise 1200mm could be slightly high due to weigh limits of the wall studs so happy with your suggestions - Due date: Flexible

I have an exiting sink cut on the stone benchtop of lenght 1180mm on the benchtop that needs rework. 1) smooth the edge n corners (edge on pic 03)and paste( fill it with) a new small piece of 480mm x 40 mm stone. 2)large Stone piece will be provided to cut the small piece for the fill in. 3) smooth the edges and provide the smooth finishing and leveling. It is small work but provide the best price and the time to complete it. Regards - Due date: Before Saturday, 14 October 2023

Wooden staircase railing has come off and we’re looking for a repairer or builder to put back into place. therailing just needs to be glue/nailed back into plcing. Nothing was broken. Materials all in tack just needs to be nailed/glued back into place. - Due date: Needs to be done on Monday, 31 July 2023

1. Drill open at the center of the pan use (5 mm drill). 2. Draw circles at an offset of 3 cm. In other words: each circle will become bigger than the previous one and the distance between each circle and the other is 3 cm. 3. Draw vertical and horizontal axis starting from the center to cross the circles. 4. Mark the intersections. 5. Drill open the marked intersections. Note: when you move from a smaller circle to a bigger circle the spacing between the holes will increase, so you need to drill extra holes in between the holes in the bigger circles. Leave around 5 cm strip all round from the outer edges of the pan as is with no holes. - Due date: Needs to be done on Monday, 26 June 2023