Find experienced local carpenters in Windsor VIC

I am looking for someone to build shelve unit in between the 2 basins to store the shampoos and create storage. This current white cabinet will be removed and replaced with this. The red fridge will be moved so I need this shelve design to go across the whole back wall. If you can build some storage or some sort to the right hand side even better. This material I want to be in stainless steel or some material that looks better then this current cabinet.

Build a plywood counter. I want to tile this completely so it’s need to be smooth even and no exposed screws. Length 120cm Width 60cm Height 100cm This photo below is a reference.

I have two 2480mm ikea bench tops that I need cut to size to fit my new cabinets but don’t have a saw. Will need 1200 length, 1750 length, 300 and 400 lengths Also need sinkhole cut out for 60cm sink Also may need to use saw to cut existing cabinets down to size to fit hot water unit etc. Electricity will be connected

Looking for build woodfired oven on site.

I'm looking out for a licensed carpenter to replace or fix a damaged door and replace a burnt kitchen top. I would please need someone to come inspect the damages 1st to accept a full quote.

Timber handrail routing Top and bottom For glazing to slot in ~30mm long Exactly 12mm wide (or 13 or 14mm) 20mm deep Need done asap Must bring all tools

I need to get painted two piece of joinery with Butterblond (DULUX S13H5),

I need help with cutting part of my kitchen benchtop and remove the cabinets underneath.

Arraching reference picture below. Flexible on design ideas.

Hi I need my wooden flooring to be repaired, the slat needs to be cut and a new piece needs to be added then strained

Butchers block style bench with cupboard space underneath and space to enclose a dryer.

Restore wood on Stairs - small mark where spilt acetone and needs repairing.

Looking a cabinet maker to complete my shop kitchen counter and cabinets

Want build in drawer / cupboards custom made between bedroom and attic around the existing door between bedroom and attic to provide more bedroom storage - See additional photos

Replace small area of flooring. Need to add new joist and floorboard. Material needs to be provided. Happy for boards to be replaced with yellow tongue. - Due date: Flexible

I'm looking for someone to clean, prep and stain my deck. Back deck is approx 4.5 x 3 metres, with two additional areas 1.2m wide x 8-9m long. If possible, Saturday or Sunday is preferred. - Due date: Flexible

Cabinet needs to be attached roughly 175cm from the ground. Size is roughly 64cm L x 44cm H x 28cm D. It does not come with screws, you will need to supply these. - Due date: Flexible

Supply materials and build a wardrobe. Something similar to the wardrobe circled in images 2-3. I have high ceilings 3.4m I think (wardrobe doesn’t have to go all the way to the ceiling). Width- looking at 150cm (replacing my ikea cubed shelf in the last photo). No drawers required. Only rails and shelves at the top to store luggage, etc (similar to first photo). Additional photo with sliding doors in the 4th photo as an example as to what it might look like (excluding drawers). White colour, any material, doors can be hinged or sliding and don’t have to be mirrored, whatever most cost effective. - Due date: Flexible

Hello I am looking to hire a cabinet maker to help convert a drying rack cupboard into three pull out drawers. See before and desired after picture. The cavity is 665D x 560W and 670H (see picture). The cavity currently has a drying rack shelf unit installed with a panel on the outside. To convert to a three drawer unit the task would require the following: 1. Remove the drying rack shelving unit 2. Install three pull out drawers at 665D and 560W (less any space required for the drawer mechanism. Each drawer must have sides and backs to ensure the contents don't fall out 3. Cut the front panel (pictured) intro three pieces to form the front of each drawer. 4. Sand each cut for easy painting at a later time and install the handle (provided) - Due date: Flexible

need someone who can cut and glue 2mm acrylic perspex to some walls and cabinets. I have $100 fee advertised but best to work out an hourly rate based on a full day work - Due date: Flexible