Find experienced local fencing contractors in South Brisbane

$150 to replace my current lattice and paint as well. I will pay for and supply all required lattice and paint, just need you to bring tools and your expertise to get the job done 😁 Total area is 3600mm x 1200mm Thank you!

Hi, I’m looking to get a 40m timber fence installed with steel posts. Also looking to retaining 1-3 sleepers high for approx 18m of the fence.

Replace fence post with Hardwood 100x100mm Post H4 Current post is 1.65 from ground so a 1.8m post should be fine.

fencing between 2 properties (around 30 meter) with gate and repairing some old existing fence (3 panels)

Install fencing and auto gate

Restore fence and replace some posts

Assist in digging holes for fence posts and installing fence panels.

We are selling a house and are needing to get a fence pailing reattached on the neighbouring property. It needs to be done today (Sunday) before settlement so the owner can restrain his dogs. Looking for someone to assist. Would ideally do all loose pavers but at a pinch just the one urgent one. Price posted is for the one

Both posts require replacing. Preferably steel/metal posts but open to suggestion. Existing gate to be re-hung. One (or more) hinges need replacing. One post is in ground, other post is in cement. Gate is quite heavy. Open to quotes on a sliding (not motorised) gate. But would prefer quote to fix existing gate. Budget negotiable depending on options.

Remove timber fence wall and take rubbish away. The timber slats are fixed to studs behind and rests on the perimeter fence with Neighbours’s. Total wall length is 6.4metres and height is 2.1 metres

One section of front fence is quite flimsy, just the area with the letterbox on attached to the gate. Might need a bit of concrete or a new post? Further photos attached of the bottom of the post.

Move already made wooden fence gate to another part of the fence and replace hole

Replace the old fence panel with a new piece. You will need to cut the new piece to fit and fix it into place.

Timber fence. Span 320cm. Height 120. Three vertical post holes with concrete required. We have all the timber material, post mix concrete, nails.

We need fence pailings installed on our side of an existing treated pine fence (new, refer photos). The fence is approximately 10 meters long and 1.8 meters high. In addition, we’d like the top of the fence cut with a circular saw/straight edge to ensure it’s consistent and level. Details: • Treated pine fence. • Approx. 10m long, 1.8m high. • Easy access to the site. We’re looking for a professional and tidy finish. Quote to include materials and AirTasker fees.

Remove and reinstall gate, and small fence onto side of chicken coop. Have all additional supplies, may possibly require further screw accessories.

I am looking for someone to source and install a side gate at our house. Preference timber that can be painted white. Width is 2m and would like 1.8H . There is a 50cm x 50cm overhang on one side of the fence (garden beneath the side of the house) that also needs to be filled in.

Front timber fence was smashed from car. We do not want a brand new fence but just for the fence to be restored to previous state (i.e., standing up and palings all in good condition). Some of the palings were damaged from the car unfortunately. We would appreciate if this could be fixed ASAP. :)

Hello. We need advice on a new double gate for the driveway. Existing is powder coated aluminium (I think) but happy to consider your recommendations on cost effective replacement.

Complete cat proof fencing. -Run wire rope 12 meters. -Attach 6 meters of chicken wire to 2.2m star pickets with right angle brackets on top. -Attach 10 meters of chicken wire to 2.5 meters to the top of star pickets and right angle brackets. -Drive one star picket in to the ground. -Put up wooden brackets which will have to be cut down to size. I have the treated pine. On top of the brackets needs to be either colour bond or corrugated roofing plastic. This has to be on top of a colour bond fence and stretching about 6 meters and 1.8 high and another 4 spots 1m x 1.8 high and attached to concrete. - the existing fencing needs to be tweaked and secured. So tightening wire ropes, using tie wire and c-clips in areas. -a pet gate to be put in one spot by being slid in between pre existing star brackets. Then tie wired on. -Balinese screening to be tie wired to shade cloth -thunderbird electric fence topper to be but on 50 meters colour bond fence. This consists of putting up 20 plastic brackets and threading wire through twice. - you will have to pick up the gate I have pre-paid for along with the roof sheeting. I have a ladder but you may need a taller one. I have a star picket driver and most of the fixings I have too. There is a bunnings 5 min drive away so I can always go and collect anything on the day needed. Please only take this job on if you are familiar with working with chicken wire and temporary fencing. It must be secure and look very presentable. Any zip ties that have been used must be snipped of and replaced with tie wire. This job is suited to someone who is familiar with this work and likes to make things look nice as well.