Find trusted local electricians in Sydney Olympic Park

2 switch boards need 2 switches replaced switches are not working. Electric points work fine.

Need to disconnect circuit

Seeking an experienced electrician or electronics engineer to replace a hardwired IEC power cable in an benchtop lab appliance to use an Australian IEC cable. The appliance is a laboratory heating bath. It has a hardwired IEC cable with a UK fused 2A plug. As the appliance will be used regularly in Australia, I would like the appliance to instead use an Australian grounded IEC cable. Because the cable is hardwired, the appliance will need to be taken apart and the new cable rewried according to AS/NZS electrical safety standards. The appliance is out of warranty but is in good working condition. The appliance is rated for 240-250 VAC, 50/60 Hz and was manufactured by Nickel Electro Ltd (Clifton brand).

Bathroom fan stopped working. The switch seems to be faulty as the key looks out of order

Downlight flickered out, replacement does not work when plugged in. The downlight model is Domus Aqua 10 - variant 21222. Issue must be to do with the power socket/mains, because the downlight + driver works elsewhere.

A few lights in the flat (bathroom) don't work even with new bulbs. General check and report on electricals in house. Lights in the living room sometimes don't switch on. Also the oven doesn't turn on. Assess and repair job for a flat in Wentworth Point.

Ceiling fan connect with bathroom switch, however it doesn’t stop when the switch turns off. - Due date: Flexible

I need a quote and measure up for electric black out curtains to be installed. Windows are 2.7M high - Due date: Flexible

The NBN outdoor team installed the utility box at the front corner of the house. The indoor team only do back to back installation. Depending on the cost, I would like the NTD to be installed at a central location upstairs where the existing FTTC NBN modem is installed (wiring won't be a problem). Or a central location near the Kitchen. The fibre will need to go from the utility box into the wall cavity (need drilling), which is a perpendicular wall. I'm happy to have a wall access panel installed near the entry point (as close to the floor as possible) to make it easier. The fibre should go up to the attic and come back down to a cabinet where the current nbn modem is installed. The 2nd option is to go 10 meter straight inside the cavity to the kitchen so I can have the NTD installed at a less visible location where we use WIFI the most. - Due date: Flexible

Needing an electrician to install LED downlights in my unit. 10 x in total. Currently only 4 x old style lights - Due date: Before Sunday, 2 July 2023

I would like to install the downlight for the whole house. Ground floor and first floor - Due date: Flexible

We need to upgrade one of our power point inside the kitchen island to the one with double sockets - Due date: Needs to be done on Tuesday, 16 May 2023

Hi taskers, anyone Willing to lend me electric impact. Just need to remove socket from my car to Replace my engine mount - Due date: Needs to be done on Thursday, 22 September 2022

Install 4 downlights in lounge room. The lounge currently has three sets of pendant lights. The downlights will be in addition to those. Downlights will be provided. - Due date: Flexible

I need a smoke alarm replacement. I've already bought a new one, but the bracket and wiring pins don't match the old one. - Due date: Flexible

Need a electrician to run 2 way switch

Someone to repair faulty 3bank battery charger More than likely power supply issue Must be a technician Power supply is 240v input 12v output

Need to install ambient lighting kit in the car - Due date: Needs to be done on Tuesday, 19 April 2022

Driver door and trunk are not locking when pressing the key. Need to check suspension, some small noise is happening when driving over the bumps. - Due date: Flexible

Have some smart light switch module to install. I know how to install, so but rather have someone with electrician license to do it properly. This job doesn’t involve major cabling. All cables are there, including neutrals. You just need to connect them to the switch module. You will need to supply some short wire to connect wall switch and the module. Please quote for 3 switch module installation.