Find a fence installation professional in Kensington VIC

Budget flexible based on material costs and selected option. Require single gate installation from side street. Preference is for iron gate, however open to other suggestions. Pictures are of existing setup. Existing gate has been mounted on adjacent fence. Fence is sagging slightly, causing gate to slump. There may also be limitations in concreting new posts (if required) due to existing fence post. Width is approximately 900mm between posts, except for towards the top where the sagging has occurred. Posts are 50mm width. No preference on height, however taller (1600+) is preferred for security purposes. - Due date: Flexible

Build a timber fence 1.5m wide and approx 2.2m high. This fence will adjoin a free standing roller door at the rear of the property. - Due date: Flexible

Hello, Looking for a carpenter or handyman to replace what looks like rotten crossbeams of back fence. Please quote. By my assessment, all 12 will need replacing and they are approximately 1900mm each of 70x40/50 sections. These should be treated timber, primed would be a plus. Access to only my side will be available and all building waste and job debris will be expected to be taken away. In addition, 3 x ~1800mm sleepers need to be removed and replaced, these are 75x200 sections No painting required. Intervention with garden should be minimised. Will have access to only my side of the fence. - Due date: Before Friday, 7 October 2022

3M roughly to protect our garden from our puppy. Need someone to come and install it as well as supply it.

Want to take the old fencing out, clear some of the planet that is on the way, and replace the fence with colorbond product and a 820mm gate at the backyard. (4200mm+3500mm)x1900mm Height, approximately 8 posts required concrete footing that goes at least 700mm deep, 450mm wide. Removing unwanted grass and rubbishes in the bush to make a clean soil surface around the house.

Approximately 20 metres of fence to be replaced at rear of residential property . Either with wood or colour bond fence. - Due date: Flexible

Needing a panel in our gate/ fence replaced.

Require someone to undertake the following tasks. - remove & dispose 10m of timber picket fence & 5 posts - supply and install 7 new 120x120 treated posts (estimate 2400 long to suit 1500mm tall stepped panels that i will install). Site is on a slight incline of approx 10deg. Work date is flexible.

I need a fence, with gate, installed across concrete driveway. Urgently needed for security and privacy. The fence to be located at the back of the carport. The width of the driveway is 2.6m and required height of fence is 1.7m. Looking for single swing gate. Would prefer colourbond but would accept timber. You will need to supply all materials, including a lock for the gate. Price subject to negotiation.

Location Kensington Task is to remove old fence (nearly completely wrecked) and build new fence Total Length is 2.4M. This will include an access gate. This is a back fence Preferably tomorrow!

Require someone to remove about 10m of timber picket fence and posts and dispose, then supply and install 7 120x120 new hardwood posts for me to install infill panels 1500mm tall. Site is on a slight incline (less than 10deg) so needs to allow for stepped panels. Date is flexible

I need a quote to replace a paling fence down the side and back of the property next to a lane say <8mtrs.

I would like to have a 6m fence built. I have 2 gates, both ~2x2.3m (see picture above). I would like someone to swap/move the gates over to build a back fence. The old back fence and roller door have been removed and area cleared. I would like one gate to be fixed to become a part of the fence and the other gate to swing open. Then add a new section of fence ~2m colorbond to close the gap.  Cut the top of the gate colorbond to the rail height. I think this is all that will be needed to be supplied:  - 4 galvanised steel posts and caps.     - Approximately ~2x2m colorbond.  - Galvanised 3 rails and 2 side rails to attach colorbong to posts. - Treated pine 2m x120mm. - 2m separating pole for the top of the fence, same as what is on top of the gates, see picture above.