Find experienced local fencing contractors in St Ives NSW

Item 1. Need to remove and install 30 metres of fence along the back - 1.8m high top and bottom rail. Preferably green. First 3 photos Item 2. Install 800 high fence along the side in front of existing which is pretty poor shape. Happy to leave as trees and shrubs cover most of it. Last three photos Need this done so dogs stop escaping into the bush and neighbours Open to suggestions on a more cost effective solution

The pool gate doesn’t latch and the gate gets stuck in the concrete paving which makes it non compliant.

Need to install 2 x pool fence by connecting them over the 3.8m timber fence. (Fence from Bunnings, as shown in the photo) and post on top of the timber fence. Aluminium fence is 2400x900mm each.

We are in main road and have a fence outside in front of the house i want to close the gaps between the bars with color bond or pine treated timber

We are looking for a single gate lockable and 1m high chain long fence along the back of our yard The current one is dilapidated so it needs to be removed and disposed of. It’s a chain link fence Approx 50LM to be installed galvanised

Pool fence required to comply with nsw pool requirements circa 20-30 metres of fencing at 1.8 m height Fence must meet compliance requirements

The boundary fence section was removed to do some landscaping and has not been tightened to the poles properly since

We are looking for quote for some to purchase and install a fence at our new rental. There are 3 seperate sections that need fencing, approximate measurements; 1 m 3m (this could be a gate, whatever is easiest/cheaper) 6m boundary fence. The fence will need to be 6ft as we have dogs that jump. Prefer Colourbond or timber happy to go with whichever is cheaper.

1. Replace hinge and attach gate to fence. May need replacement panel. 2. Replace pool latch for another gate. Pictures attached.

Supply and fit pool fence screen using this ekodeck castellated panel from bunings

Drill into Metal pool fence to install perspex as to meet with pool compliance. Must bring own tools & screws please. I have the sheet of Perspex.

Hello, I have a front veranda that currently has a metal fence. I would like to get a higher fence installed with smaller gaps than the current one . The area is around 12m long and I would like a minimum of 1200high. The area would need a gate installed too. I will send pics of the current area . I’m wondering if pvc is the cheapest option . Thanks Robyn

Removal of front and side brick fence 1.8m high 24 metres long single skin. Access good as this is the front fence you can park truck or skip next to fence.

Replace exisitng aluminium pool fencing approximately 5.7 metres in length plus pool gate (approx 1 metre) including self closing hinges and magna latch etc (must be pool compliant).

Driveway to be relaid, levelled, new gate to be installed.

36 mt lenght 13 mt is 1.8 mt high 7 mt is 1.6 mt high 13 mt is 1.2 mt high - Due date: Flexible

I need 4 pool fence posts removed. Ideally dug out (the concrete bases are small but about 30cm deep) or angle ground out. The posts are 5cm square. Hollow metal over a concrete base. - Due date: Flexible

Construct 5 new brushwood fence panels on an existing/repaired frame. ● Remove the existing fence and tip. ● Straighten posts where needed. ● Install top lateral support rail. ●replace 5 panels with new brushwood panels. ● The fence will sit on a treated pine base. ● The top of the fence will be finished with a brush roll capping. - Due date: Needs to be done on Thursday, 12 October 2023

Construct and relace 5 panels new brushwood fence on an existing/repaired frame. ● Remove the existing fence and tip. ● Straighten posts where needed. ● Install top lateral support rail. ●replace 5 panels with new brushwood panels. ● The fence will sit on a treated pine base. ● The top of the fence will be finished with a brush roll capping. - Due date: Before Thursday, 12 October 2023

1 day two men (full day) to install swimming pool fence (half metal fence and half glass fence) - fence material and screws are ready but you need to have cutting metal equipment and drilling hole equipment (10mm dia holes) 1. Cut 7 old existing metal pool posts (50mm*50mm)prior to new installations- see photos - cutting equipment by you 2. for metal parts of the fence install 7 screw posts on pavement and install metal fence 3. for glass part Install 30 spigots - each has 4 screws of 10mm dia and 75mm length ( = 30*4=120 holes) - holes to be drilled on sandstone pavement - you to provide drilling equipments (I have spigot and screws ready, and location of holes already marked on ground) and finally place glasses on spigots -see pictures - Due date: Needs to be done on Monday, 12 June 2023