Find experienced local fencing contractors in Willoughby NSW

Timber fence and gate replacement.

Fence repair as shown in the picture.

We need to install panels, which can be purchased from Bunnings, with dimensions of 900mm x 1800mm. Two panels are required for each side of a space measuring 1.8m x 1.6m. The panels will hang down and be fixed with black posts, the panels won't beed to be cute. Please advise if you can bring the posts. The cost of the materials you provide for the installation can be added to the labor price.

Repair place back two fence railings on small dome and make my side fence dog proof she keeps getting out.

I need someone to install an Oscillot cat fencing system for my courtyard. Product has arrived and just needs to be installed. Fence line is approximately 14 metres long.

Measure, quote, supply and installation of a combination of Colorbobd perimeter at the backyard (~20m) and fence plus gate at the front yard (~15m). The solution for the front yard should provide good street appeal, good privacy and minimise street noise. The gate is for a single car, preferably sliding motorised.

In install 15 metre Pool fence. L shaped + install a gate. The fence dimensions are 2.4 by 1.8. The boxes need to be dug into the footings and cemented. We will supply all the materials including the fence and gates Must have experience with pool fencing - Due date: Before Wednesday, 20 December 2023

build side fence infront yard and repair other side. replce 3 panels of palings on back fence. - Due date: Needs to be done on Thursday, 13 July 2023

the pool is 6 x 11 meters. looking for a glass fence to be installed - Due date: Flexible

Replace existing fence panels will need to cut to size all materials supplied. 8 panels to be fitted. - Due date: Needs to be done on Wednesday, 21 December 2022

I have a section of fence that is too short and is leaving a gap at the bottom. I need the existing 1.8m fence palings taken off and replaced with 2.1m palings. There is a slight slope to the ground. I will supply the 2.1m palings. There are 45 palings (100mm x 15mm) that need replacing. - Due date: Before Sunday, 21 August 2022

I need a wall built to replace my existing timber boundary fence. The fence should be built using cement sheeting and ideally with metal posts to last much longer than timber. A product like hardie fine texture with minimal vertical jointing would be preferred. The fence should be built with a level top edge stepping down where necessary to accommodate the very gradual slope and ensure a fence height of between 1.8 and 2.1 m. The fence is just under 9m long. The fence will continue on from a rendered block fence (see photos) and needs to look similar. It continues past a glass pool fence and finishes about 3m into our pool area where it joins to another block wall (the neighbours garage). The wall needs to pass no more than 50mm away from the glass pool fence. The wall should be clad on both sides. There is a rainwater tap attached to a post that will need to be attached to the fence instead. Ground level is the roughly the same on neighbour and my side of the fence, no more than 100mm difference. There is a hole on my side of the fence where I removed a tree stump. It's approximately 600mm deep by 600mm diameter. Note: Hardie Fine texture sheet are already prepped for painting. If you are quoting based on a different sheet type, please include details of the sheet type and whether the joints are the similar or different to the Hardie Fine texture product. Also include prep for painting in your quote if the sheet is not already prepped. Please include removal of existing timber fence in your offer. Please submit details of your quote with your offer. I am happy to provide more details of the job if required to quote, just ask. Job can be done any time between now and due date.

Help my workers pull down fence dig holes put posts in - Due date: Needs to be done on Tuesday, 7th Dec 2021

New wooden fence needed in Willoughby NSW. Length is 34 metres. Most of the fence will be 2.1m but up 10 or so metres may be 1.8m high. Looking for a lap and cap fence. Need to have the existing fence removed too. Would like someone to start in the week beginning 6 September. Thank you. Scott

I require the length of my fence to be replaced. This is approximately 50m from front to back. The height required for majority of the fence is 2.1m - aside from waist height at the frontward. We are based in Willoughby and flexible/ available immediately.

I require my exisiting neighbouring fence to be removed and replaced as it is old and damaged. The height required would be 2m+ and this would span the entire length of the boundary fence - approximately 50m. We are based in Willoughby and are available immediately.

The bottom wooden frame in the bunkbed has split and needs to be replaced (don’t think repair is an option). Will pay for cost of materials and labour.

I have an already existing fence that I need to nail 200 x 1800 high treated pine fence palings for swimming pool compliance. I need a supply and install quote thanks

Job included: 1. removal of the lattice fencing (urgently) 3m~ 2. put in wooden fencing 3m~ 3. replacing the exiting timber fencing with new fencing 15m~ task 1 to be completed immediately, 2 & 3 to be completed later