Find a professional garden bench contractor in NSW

Mirror and few electric work , Some garden work

Have removed some plants in a small area. Need flat Deck (100 inches) at the tile level and a bench seat with back rest on the other. (90 inch) with arm rest as shown in pic 1. Pic 2 is the area as is now and pic 3 is how the deck and bench needs to be. (Front bench and bright yellow deck at tile level)

Hi, I need a garden bench and empty bbq gas bottle removed and a small rust spot removed from outdoor tiles and veranda washed with dishwasher liquid and hosed off. It must be completed today. It would take about approximately 30 minutes to complete. Must use product in photo to remove the rust spot. You’ll need rust product in photo. Rags to remove rust. Broom to assist with cleaning back veranda and only use dishwashing liquid to clean veranda tiles. There is a hose near by to flush tiles clean at end of job. Will need photos before payment.

Restoration of a garden sitting bench. Replace wooden slats approx 1220mm x 55-60mm x 15mm along with rusted bolts

Assembly garden bench. Easy to assemble

Our tennis club has 2 new garden bench seats that need to be assembled. attached is a picture of one we have already.

Two garden benches need to be painted after sanding them both

I’m looking to have a roof and bench built. I’d provide materials. Labour, pick up of materials and knowledge needed only. - Due date: Flexible

Put together a painted wood flat pack garden storage Bench/seat - will need to supply own tools. It is same as photos but painted white. Brand is Rivercity House & Home Co. - Due date: Needs to be done on Saturday, 11 November 2023

We have a wooden garden bench/table and it came with a 4cm diameter hole for our umbrella/parasol. We need the hole to be cut out a little wider to approx 6cm to allow our umbrella/parasol to fit. - Due date: Flexible

Simple timber garden bench needs planks replaced and painted. I have the paint but not the timber. - Due date: Flexible

Fix tool holder to the wall and assemble a garden bench - Due date: Before Saturday, 17 June 2023

Pick up door within 5 min drive, take off the door to be replaced and put new one on. Assemble 2 new garden wood bench seats currently in boxes - Due date: Flexible

I have a 4 tiered garden bed in my backyard. I would like 3 out of the 4 garden beds to be topped with timber to make them into benches. Just need a timber bench made over the top only, using the already made garden beds as the base. On the left and right side of the garden bed there is a small gap between the fences which I require to be covered, only 76x 20cm approx. Summary: 5 x items in total. 1. Far left small fence gap 2. Far left bench top 3. Middle bench top 4. Far right small fence gap 5. Far right lower bench top See images attached. The benches and fence will be later painted white so the wood to be used doesn’t have to be pretty, just needs to match and suit appropriately. Measurements in images are approx. - Due date: Flexible

Restore a Baltic pine table and paint 2 wooden benches white - Due date: Flexible

Complete assembling garden storage bench box bought from Complete Storage. Assembly instructions are all pictorial, no words. Hinges are not attached and cover is off centre. Also plastic lining needs to be put in. - Due date: Before Sunday, 11 December 2022

I have a bench box or horizontal toolshed - made almost entirely of wood. The lid of the box is large & heavy. The lid is attached to the rear (southern) wall of the box by four sets of hinges. There are also 2 piston-like closers at each end which provide a degree of control when opening/lifting and closing/dropping the front of the lid. The bench box was constructed in 2007. In 2017, the hinges were replaced with new hinges. The hinges themselves are still in good condition. However the upper halves of the hinges, which are attached to the (southern) rear of the lid, have come away from the lid because the wood to which they are attached has rotted. The top of the external part of the rear wall of the box used to be covered by metal flashing. The part of the flashing protecting the western half of the external rear wall has disappeared. In addition, on its western side, the bench box is located right next to a leaking pond. In addition, in the bottom of the bench box is a pump sump which always has at least a few cms of water in it. The result is that, at least in the current weather, the wood comprising the rear wall of the box is very wet. There is an access problem. The outside rear of the box is very difficult to access as there is only a 6-7 cm gap between it and the fence behind the box – AND there is mature bamboo growing in that gap. As a result, working on the rear wall of the box will require removal of the lid and working on the rear wall from inside the box (noting that a portion of the floor is occupied by the pump sump). The main part of the task is to replace as much of the lid and the rear wall of the box as is necessary to allow the lid hinges to be attached to sound new wood in the rear box wall. I am open to replacing part or all of the wood in bottom (southern) side of the lid with something which can cope with moisture. Also, the piston-closers need to be replaced. - Due date: Flexible

Old timber garden bench needs the legs reattached and a paint. - Due date: Flexible

We would like an Airtasker to assemble 2 Matrix Planter box kits and fit the accompanying screens, assemble a 2 seater steel garden bench and 2 pieces of office furniture. Please bring gloves and tools ( including a drill)) to assemble the items. - Due date: Needs to be done on Sunday, 10 July 2022

Need a cabinet door repaired and also want to make a garden bench from my fence which i am pulling down - Due date: Flexible