Find a professional gate installation in Abbotsford VIC

move side gate further up the path to avoid knocking against the down pipe. Replace door frame around the toilet door - damaged due to washing machine leaking

We need to put a gate lock on our studio door. You will need to come and see the door first to discuss the best option.

Fix Back gate that is currently “sticking” at top (non hinge) side of gate. Suspect this is most likely due to slight movement of fence and gate. I believe the required fix is to (supply) and install an additional hinge near the top of the gate. Gate and fence are approx 2m high. Current hinges are rivet screws.

Our secure metal gate isn’t so secure. An intruder could reach through and turn the knob. Whoops. Would like a well-rated Handyperson/welder to come and resolve the problem, we think by sourcing a small metal plate and welding it beside the lock, but if there’s a better way of doing it that would solve the problem and look better than that solution please speak up! Photos attached show the problem. Looks like steel to me but you’ll know better than I will.

Noticed water stain in the last week. No leaking detected during recent rains. Scope of work is to: - investigate the potential leak; - fix leak; and - fix plasterboard.

The gate is attached to a wooden support post which is bolted into the brick fence. The bots holding the support post into the brick fence have come loose so the bolts either need to be resecured or replaced. Photos show the bolts that have come loose.

Broken fence pailings around 4 bed to be fixed nail gun could do the trick or hammer and nail

Cut and weld to top of the gate. Gate scrapes on upright closer post which is level. Need a small slither of top of gate edge cut off, then Re welded with edge piece. 40cm x 10mm approx long cut off edge of gate to allow gate to function as intended .

Just need to re attach two wooden panels to the top and bottom of gate and would like to add some form of backing to said fence so you can’t see through the slats

- Installation of an iSmartGate smart garage door controller - iSmartGate Lite with door sensor - Roller door uses a ShedMaster GDO-8 - Power outlet already available - Due date: Flexible

Looking for a licensed plumber with good inspections background to have a good look at our plumbing to see what might be causing a lingering bad smell (you know the one). It’s up on the third floor of a converted warehouse, so might be trickier than some. Attaching some photos of the culprit and where I THINK the pipes are housed. Just looking for cost to investigate at this stage. - Due date: Needs to be done on Tuesday, 29 August 2023

Gate hinges need replacing. Three or maybe four gate hinges needed to be fixed to a metal gate. Not necessary to weld but can be drilled into the metal frame. - Due date: Flexible

We want someone to cut off the end of one spoke on our front gate so our cats can fit underneath. It needs to be not sharp so probably sawed off and sanded (smooth) Must supply own tools. Day is flexible

Some bricks have dislodged at the bottom hinge of large steel gate. About 6-8 bricks need to be replaced and the hinge & bracket need to be re-fixed with new masonry anchors. We've got spare bricks on site. - Due date: Flexible

the property is a shop. at the back of the shop we need a metal pedestrian gate installed - Due date: Flexible

The latch on our gate is misaligned - has been since we moved here. Need someone to take a look and decide the best way to repair. See photos - the horizontal bar strikes too high on the latch. Job in Abbotsford, near the convent.

Two jobs: 1. Gate The door isn't closing properly as the structure has come out of place. 2. Kitchen cupboard Door has come undone and needs repairing Give me a quote on 1 or both jobs please.

We need to get a fence installed. Approximately 12m of fencing is required. There are 2 sections of fencing that need to be done - 1 side and 1 rear fence, each 6m in total and the back fence will need a gate built too.