Find a professional gate installation in Baulkham Hills

Trim one edge of new wooden gate to fit exiting opening and cut hole for bolt access to open the gate See photos of existing and new gates for reference Hang new gate Hinges and bolt supplied Trolley available here to assist with moving gate. Gate is heavy to move and if needed second person here will be available to assist with moving and hanging the gate. Please bring all tools required to complete this task

I need a compliant pool gate to be provided and installed as per the following details: Size: 120cm height (minimum) x 111cm width. Features: * Magnetic latch pool safety lock and self closing hinges (from any positions). * Location of the lock is shown in the picture. * The gate should open/swing only in a direction away from the pool area. * Colour to match the existing fence (as per the image). Notes: * Gate and all materials should be provided and mounted. * The work must get approval from the council inspector. Here is the advice by the local council for compliance: * Pool gate must be made child-safe by means of a lock, latch, bolt, chain or other child-resistant device, located at least 1.5m above floor level. * The access gate/s shall be fitted with an automatic closing device that will shut the gate and operate the latching mechanism from any position, even with the striker resting on the latching mechanism. * The access gate/s shall be mounted so that they swing only in a direction away from the pool area. Thank you.

Side gate of colorbond material doesn’t lock properly . May need to be shaved slightly

Approximately 0.9m wide between the fence and the house. I will purchase the gate if you recommend where and what design.

Replace 6 hinges on 3 sagging metal gates with self closing hinges. DESCRIPTION OF CURRENT STATE Gate 1, the gap for the bottom hinge and the post is 2.1 cm, the gap for the top hinge is 2.4cm. The top part of the metal gate is hitting the post and the gate cannot close properly (see gate1, gate_not_closing photos). I have taken away the Magna-Latch to stop it rubbing against the post. Gate 2, the gate can close but catches on part of the latch and is stiff. The gap for the top and bottom hinges are approximately 2.1cm (see gate2_stiff photo) Gate 3 works normally (see gate3 photo) A close up has also been provided of existing hinges for all three gates (see existing hinge photo) WORK REQUIRED For Gates 1, 2 and 3, replace existing hinges with D&D hinges, adjust the self closing mechanism on the hinges so that the gate closes smoothly and Magna-Latch operates properly. (Gate 1 requires reinstallation of Magna-Latch). I shall provide the 6 D&D hinges.

Ditec driveway gate remote stopped working. I have one more remote which works well. Need second remote set up to work with driveway gate (Ditec)

seeking quotes for someone to supply and install white PVC panel gate and small side panel. total width 1700mm gate width 800mm - 900mm

Hello! I need someone to fix the damaged entry gate at my property. The damage is due vehicle collision. Please provide a quote for the work. The gate is made out of steel with SHS frame and rod grills. Thanks

This drawer was put together with a couple of screws missing. There are two screws that go through the bracket into the back of the door missing. Require these to be fitted, or, the door can be fixed with an alternate method as long as it looks clean. The gate needs to be raised slightly to prevent scraping at the bottom. The cord to open needs to be shuffled across and fixed to fence for easy opening from both sides.

Need to build a side boundary gate with Colorbond that preferably matches the side fence Color. The gate needs to have a lock. The gate can be attached to the existing pillar.

The side gate hinge (image attached) requires fixing. The rivet is broken, but I am open to a workaround that can securely hold the gate together and allow it to rotate on the hinge. Please note that the hole on the bracket is narrower than the hole in the gate. It might be necessary to do some drilling to make them consistent. - Due date: Flexible

Gate Hinge has collapsed from brick work, need repair to secure yard - Due date: Needs to be done on Wednesday, 3 January 2024

Have a backyard with 10 X 8 with concrete pavers and grass. Need to have timber or composite decking with pergola and enclosures. - Due date: Flexible

Looking for someone who can build and install a picket fence gate for this backyard picket fence. There is currently a Gazebo standing at the gate's position, the gate may need to be installed onto the Gazebo's timber poles. Gate width: 1320mm Fence/Gate height: 1213mm Location: Baulkham Hills

We need a Colorbond double gate (1800mm high and approximately 3000mm wide) - Due date: Flexible

Needing two Aluminum slate gate horizontal monument 1,5m wide with key push lock - Due date: Flexible

My townhouse fence gate latch is broken. Will need to be fixed or replaced. - Due date: Flexible

Repair pool gate to ensure it self latches. May include installing new mechanism and hinges or replacing panel to ensure gate closes and self latches. Must be on site at 7 am as owner is not always home. - Due date: Before Thursday, 29 June 2023

Supply and Install 18 metres of white, spear and loop pool fencing 1.2m high on a concrete path around an inground pool. - Due date: Before Friday, 19 May 2023

We removed side gate during rendering the house which now need reinstalling back to where it was, bit of adjustment required. Happy to pay for any addon material.Thanks - Due date: Flexible