Find a professional gate installation in Collaroy Plateau

We have just purchased a house in Collaroy Plateau which is not puppy proof for our German Shepherd. The perimeter fences are dog proof but there are no gates on either side of the house. We need someone who can build two gates that are dog proof and that fit in with the timber work on the house such as the balustrade and timber slat cladding on the ground floor. We would like you to measure up the gates and agree on a design with us on the Saturday 25/5 then come back the next week to make and swing them. There may be a fixed panel required to fill the opening aswell. I won't have any photos until Saturday when we move in. The gate goes across the top of the steps with a fixed panel across the top of the drop and we want it to blend in with the slats as shown in the other pic. About 1400 to 1600mm high should do but will be guided by you. The other side of the house is same type of gate and similar size.

Bolt on aluminium gate needs to be moved to enable gate to open fully - Due date: Flexible

TWO GATES. COLOUR BOND STEEL FRONT GATE NEEDS NEW LOCKING DEVICE TO BE PURCHASED BY HANDY PERSON AFTER I OK IT AND INSTALLED BECAUSE IT SWELLS WHEN HOT AND CANT TURN HANDLE AND PUSH OPEN. RUBBING BADLY ON FRAME OF FENCE AND BACK GATE IS CATCHING ON LOCKING DEVICE WHEN TRYING TO OPEN. can come and look at what need to be done first. - Due date: Flexible

Supply new 900 x 1800 gate with pad bolt latch and hinges. Remove old gate and trim new gate to size. Fit galvanised hinges and pad bolt. Dispose of old gate. - Due date: Flexible

Hi I require a gate(s) replaced. Basically the one in the photo has a damaged post so is not closing correctly. As such I need: 1) An aluminium type gate setup. a. Possibly open to timber style b. Just not sure fixings will hold….. c. My thoughts are timber may be too heavy….. d. But I may be wrong & not experienced enough, so good to get advice. 2) Allows access for car to move up drive – very occasionally. 3) So cannot have a permanent middle Post. 4) Needs to be “vertical / horizontal finish” as opposed to the “round “ style in the photo a. Because we have fence in front of house which is more “ squared palings style.” Needs to match style. 5) The old posts will need to be removed.....they are cemented in to ground. 6) Current height is 1.2m approx - i possibly require slightly higher - up to 1.6M – the height is optional given standard sizings etc.... 7) Width is approx 2.7m in total from wall to side of house. Photos show: 1) gate which needs replacing 2) & fence at front of house to match style to. - Due date: Flexible

We have removed a colorbond fence panel between neighbouring properties, and require a gate between the two that the kids can open but dog can’t get through. Either timber or colorbond, automatic close, basic latch (no lock). - Due date: Before Thursday, 3 November 2022

There is a dent in the back of my Ford Ranger ute. It is at the top of the tailgate - Due date: Flexible

We need two new gates to keep a dog in our garden. Timber construction is fine. First gate is about 166cm wide x 100cm high (needs to fit at top of a few stairs). Second is about 120cm wide by 100cm high. Just need a basic mechanism to keep them closed, don’t need to lock.

The bottom hinge on the front gate to our driveway has broken - requires fixing / replacing. The gate is made from aluminium - I'd like the current hing cut off, a new hinge welded on and painted black. If another hinge is required to hold the weight as well this would be fine - welded to the post and the frame, and also painted black. - Due date: Sometime before November would be ideal

Need a new gate. Aluminum or Timber. All parts down to the screws need to be high grade marine grade non rust fittings. All door furniture and hinges required including lock/latch. The gate should sit independent of the current fence which will need replacing in the not too distant future (i dont want to replace the gate again). Colour should match the current Merbau fence. Prefer timber look aluminium if available-otherwise something that blends in. The existing posts have rusted through and need new ones. Full Zinc/marine proof grade. I dont want the a similar gate/latch to what is currently there. I need a proper gate latch that catches even if there is a bit of movement. Current dimensions post to post: 1.94m Height 1.4m

I have a black decal that I need help installing onto a Ford Ranger tailgate. I attempted to install it myself the first time and buggered it up with creases and bubbles. happy to bring the car to place within Collaroy/Brookvale areas. Timing and price negotiable