Find an experienced handyman in Herston

Hello. I need someone how can to repair a wood door in garage. The door was hit by a car, and it broke and came off. The price can be negotiated and changed.

There is small dent in garage door

I have the replacement hinges on hand. I need the screen to be take apart and re-assembled including the repair of one section.

Need run internal pathway from the IDF in the garage using conduit with a draw wire to downstairs study.

We have very long aluminium gutter tracks that need to be taken downstairs. They are too long to fit around the stairs. I need someone with a circular saw to come and cut the aluminium, which is about 20 metres long, and either leave it with us or take it away.

Hello I need to box around this gas hot water system. Approx 900mm from the ground and 500mm wide and a hook on the wall to hang the electricity cord image attached. The material to use is smooth pine. PLUS Water-damaged window frame that needs new framing

Need the old holes of the toilet-roll holder plastered up and need the toilet roll holder hung in a different spot - screws and wall inserts for holder provided, need to bring own tools and plaster etc.

Lay the metal straight, Weld and then place the Pillar with the grate on top. . Once the metal is straight, the pillar is attached with two screws and then the fence is nailed to the 4 corners. . I am attaching a photo of how the metal should look with the pillar. I also receive a quote.

Hello, I am looking for someone to install a manhole in the location of the first photo. the second photo is similar to what I want- something clean/slimline. Avoiding the bulky framing would be preferable. I don’t have a stud finder to confirm studs and electrical, so I understand the location may need to move. Preferred area is 1.2 x 1.1m. This is in a single level unit- no one above me. Can complete anytime between 11/09 and 22/9, excluding Tuesdays. Can you please include your qualifications and availability in your offer, and preferably a link to (or advise) which manhole you would recommend based on the above. Thank you 😊

I have a large hole in the wall that needs to be repaired asap.

I have a few little jobs to be done at Herston. There is a hole in the ceiling approx 1m x 1m, a couple of small holes in a wall, 1 x chipped corner, and dents to smooth out.

My garage got damaged and it need fixing.Its made of wooden boards

Balcony tiles are missing and cracked. Retile these to best match existing.

Need 160m2 of gyprock sheeted, square set, joined, patched and finished, job is over 2 levels, ceiling heights of 4m on the first level (80m2) ceiling heights of 2.9m on second level (80m2). Need 8x 50mm holes for amenities on either level (16 in total). Painting not required. Photos attached

Person handy with tools and common sense to install a SOG system into a caravan/motorhome

Have balloons that I need blown and set up on a backdrop arch

Hi, will be needing most likely X4 new risers for roof lift. Possible inner pushing rods for 2 currently X2 cables have snapped at rear Model-2016 Jayco swan outback. Looks like we will be needing X4 new eye bolts X1 cable I can see has pulled off but still intact. Roof seal needs to be done with specific sealer. I can provide, will work out what is best as your the professional. Located Herston can bring to you for a week if need be to get the work done will be financial for the full amount as of the 24th. Cheers Gavin.

Hi, have a sag in the roof of a camper causing it to have a small leak. Will need a full reseal done and H-frame installed around the aircon to push it back up. If we can keep the roof on to brace and seal that would be alot less labour. Will be wanting to use quality Sealant, V4 or verseseal. Timber frame. I can do that if need be. Located in Herston I can bring it to you. Cheers Gavin.

My sliding door has come off it’s rail and is stuck open. I need someone to get it back on its track.

Bloke I bought my ute off did a dodgy job mounting side steps and rails. Just need someone to fix the mounting up. Not a huge job Just where steps mount to chassis probably need some simple mounts made up