A white van parked on a street, with a person standing next to it, ready to load or unload items.
A white van parked on a street, with a person standing next to it, ready to load or unload items.

Find a professional hot water system contractor in Southern Highlands

Fill in a short form and get free quotes for local hot water system contractors in Southern Highlands

4.3

Excellent rating - 4.3/5 (10900+ reviews)

Looking for hot water system contractors?

  • Gas system
  • Electric systems
  • Boilers
  • … or anything else
It only takes 2 minutes. And it's free.
Up to 50% cheaper than franchise dealers
No job too big or small
Free insurance coverage
Secure cashless payments
Same day or next day service at no extra cost

Recent Hot Water System Installation & Repair tasks in Southern Highlands

Hot water system

$300

Ulladulla NSW, Australia

18th Oct 2024

Hot water cylinder connected

Replace LP Gas inlet on caravan Hot Water Service

$500

Balaclava NSW, Australia

15th Jul 2024

Replace LP Gas inlet on caravan Hot Water Service. Gas HWS is Suburban SW6DEA model. Must be certified person

Plumbing and hot water

$1,111

Sussex Inlet NSW, Australia

7th Feb 2024

Install hot water system, connect toilet to sewer line, connect kitchen to water and drainage

Check out more tasks in your area

What is Airtasker?

Post your task

Post your task

Tell us what you need, it's FREE to post.

Review offers

Review offers

Get offers from trusted Taskers and view profiles.

Get it done

Get it done

Choose the right person for your task and get it done.

Now Available
  • Get it done now. Pay later.
  • Repay in 4 fortnightly instalments
  • No interest
  • Available on payments up to $1,500

What do hot water system installation services include?

Hot water system installation services include all the activities necessary to put a reliable, safe hot water system in your home. This involves installing an unvented hot water system, inspecting the installation area, preparing materials, installing the cylinder or tank, then making the needed connections. After the installation, your plumber can test the system for flaws and address them as needed.

Inspecting installation area

Your water heater installation begins with a thorough inspection of the spot that will house the tank and its components. Your plumber makes sure that the floor is robust enough to support the cylinder's weight and complies with established building codes and safety rules and regulations. If the allotted space is deemed insufficient for the cylinder, your plumber can help you look for an alternative spot for the unvented cylinder service. 

Preparing for installation 

Your plumber makes the necessary preparations for the hot water cylinder installation. If necessary, some plumbers may offer to make an improvised platform of sturdy materials to support the tank's weight. Otherwise, you can hire a Tasker to handle all your carpentry needs.

When appropriate, your hired plumber shuts off the power, gas, and water supply before starting the job. They can take all the necessary measurements to determine the right amount of materials, then cuts and bends wires and pipes to the appropriate lengths and widths. Your plumber may also cut holes into walls or floors as needed to allow pipes or wires to run through.

Installing the cylinder

Once the cylinder's space is ready, your plumber can proceed with the unvented hot water cylinder installation. They can place the cylinder or tank onto its designated space and position. Your plumber takes care not to damage any of the components of the vented hot water cylinder or other pipes and wires in its surroundings.

Installing components and pipes

After the cylinder is in position, your specialist proceeds with attaching the appropriate pipes, wires and components like the Temperature and Pressure Release valve, expansion vessel, immersion heater, and any other pipes and valves. As with all other stages of the unvented cylinder installation, they use appropriate materials and techniques that are compliant with state safety and building regulations and industry best practices. 

Testing the system

Your hired plumber tests the system after completing the installation. They check that each tap and shower head provides hot water on demand and flows with consistent pressure. Should variations in temperature or pressure arise, your plumber can troubleshoot the system and do the appropriate fixes. 

They repeat this process until the hot water system works without any issues. And now that your home has hot water running through your taps, tubs, and showers, why not ensure greater warmth and comfort in every room of your home? On Airtasker, you can also hire an insulation installer who can help you cut down on bills and achieve year-round comfort.

Recent Hot Water System Installation & Repair tasks in Southern Highlands

Electric hot water system

$75

Bowral NSW, Australia

12th Jun 2023

My hot water system isn’t heating up it’s electric - Due date: Needs to be done on Monday, 12 June 2023 or asap Price per negotiation

Hot water unit in garage for

$200

Vincentia NSW, Australia

8th Nov 2022

I’ve changed my hot water unit to heat pump Would like my old unit installed in my garage to have hot water in the shower that’s inside my garage. Some plumbing work as well. If you can come give me a quote - Due date: Flexible

Hot water problem

$250

Colo Vale NSW, Australia

12th Jun 2022

Just moved into a new house and there is no hot water, I think the pilot light has stopped working there’s no noises from the hot water system.

Hot water gas heater service

$200

Shoalhaven Heads NSW, Australia

29th Sep 2021

The pilot light on the hot water heater no longer lights. I assume the pilot light gas line is blocked? I would like the pilot light serviced / repaired so it is operational and check the unit overall.

Hot water plumber or electrician

$300

Sussex Inlet NSW, Australia

10th Apr 2021

Hot water system is not heating. Need a hot water plumber or electrician that can test and supply and install a new thermostat or element (I’m guessing this is the part that has failed?). The tank looks fine, not rusted or leaking. It is a Rheem 250 ltr tank. Model number 11125008. Need done by 11/4/21 please.