Find a professional wrought iron fence service in VIC

4 meter cast iron fence on brick and bluestone foundations. Needs stabilising and fixed with new foundations.

We are looking to install boundary iron fence and gates. Products importing from overseas and seeking installer. Installer must be able to come / inspect / measure and confirm sizing and installation. Cost to be discussed. Measure up the site in advance and confirm drawings. Must have dealt with similar projects. Around 40 m fence and 2 x swing gates to the boundary.

We are looking to install boundary iron fence and gates. Products importing from overseas and seeking installer. Measure up the site in advance and confirm drawings. Must have dealt with similar projects. Around 40 m fence and 2 x swing gates to the boundary.

Medium height iron gates for the front fence

existing iron gate needs to be attached by bolts after being snapped/pulled off bolts still in holes

Needs cross timber beams replaced, reuse iron sheets (if possible) and the base of fence needs to be renewed.

Looking for someone to install a gate. The striker plate is already bolted to the wall however it does look a little low. I need a post hole dug to support a heavy gate. Gate is only 900 wide however it’s cast iron, so very heavy. Hole will need to be approx 800mm deep and 400mm wide. Ground is clay but I’ve got through it before with shovel for large trees. A good post hole digger will get through it. All materials to be supplied - Due date: Flexible

Provide a quote to install wrought iron fence on top of existing short concrete block fence and install a gate. 3 meters by 2 meters area. - Due date: Flexible - Due date: Needs to be done on Thursday, 25 January 2024

Repair bent gate, would like additional quote if able to powder quote - Due date: Flexible

The fence section is about 15 metres. The wooden rails on the other side have rotted but the seven steel supports in the ground are still strong and the iron sheets can be reused. Bolts should be replaced and there could be as many as 280 involved. Plants on that side will be cleared before work starts. The section of fence runs from the side of a shed to the back of a house and a newer fence. The steel posts are about 2.6 metres apart. About 15 metres of wood is needed for the length of iron involved - the wood that is there now has rotted. Work could be done in early January instead but preference given to earlier. Also happy to discuss costings if you can tell me what the wood (treated pine) would cost, and how much labour is involved. - Due date: Before Friday, 22 December 2023

Suply & install black wrought iron spear head gate & side panels width 2.7 m , height 1.8 m ASAP - Due date: Before Friday, 1 December 2023

Post and hinge my existing wrought iron gate to the house.nees a post with catch or lock opposite side - Due date: Before Monday, 11 September 2023

We already have a brick fence built in the front of our house need iron wrought inserts to be made and installed Below are the dimensions for each insert and the gate 2.37×0.66m 2.24x0.66m 2.545x0.66m Gate 1.72 x 1.22m - Due date: Before Tuesday, 31 January 2023 - Due date: Flexible - Due date: Flexible

Remove wrought iron gate. Don’t mind if it’s cut away - Due date: Flexible

iron fencing and gate installment - Due date: Flexible

I need someone who has experience in installing a fence at my roperty. It's a small property with two drive ways. I need iron fences and two manually sliding gates. - Due date: Flexible

I live at the end of a straight and it's great and a car smashed into the fence and to the fence and gates and then into the house I need wrought iron like gates replaced replace and the fence fixed

My iron gate open both sides, each side of gate width about 1.8 m. I would like to add electric gate opener for it. The electric gate opener is provided by me, but I have not bought it yet. The installation date can be flexible. - Due date: Flexible

I need an iron gate latch bent as the design of the gate doesn’t allow for a standard straight latch. My dad has tried heating the iron with a heat gun - but it isn’t hot enough. I’m a solo mum and can’t figure out how to bend this myself! The fence installer somehow bent the last one - but it only lasted about 2 months before it broke. - Due date: Flexible

3mtr double swing gates (70kg each) with 2 steel posts to be installed at top of driveway. Cement footings required to fix posts at ground level. To be completed within the next 2 weeks. - Due date: Before Friday, 17 February 2023