Find a local Tasker to help you make a kitchen cabinet in Melbourne

I need someone to dismantle existing kitchen cabinets and install new ones. I have already purchased the new cabinets. I'll also need to remove the current oven rangehood and put a new one. Pictures show the current kitchen and plans for the new kitchen

Solid timber cabinet doors and bench top painted

I need a cabinet maker to make kitchen cabinets , laundry cabinets and wardrobes for a full home renovation project

Hi there, I'm after someone to adjust some kitchen cabinets, as the hinges have come loose, causing the cabinets to drop

In MID December I am wanting to install a new wall oven measuring 895W x 572D x 596H (mm) into the space occupied by the oven in the photos. The new oven will be approximately 30 cm’s wider, and I need the cupboards modified to accommodate the new oven. Ideally, I need a cabinet maker to prepare the space for the existing oven’s removal and to reconfigure the cupboards post the new oven being installed. Cupboards must match existing

Install 4 pull out storage in kitchen cabinet. Fix the Baton with screws. Install the slider and hook the basket. Slider will stay one side on baton and other side on cabinet wall. Cabinet is narrow with 240mm wide and 650mm depth Baskets are 200mm wide and 600mm depth You may have to bring 8 x 35mm screws for batons Please let me know the best quote Demo installation: https://youtu.be/TVBG6rigr3o?si=YiAhB_wmXWq1n8vG

Reinstall kitchen cabinets. Also some general carpentry work, hanging doors, a bit of plaster, laying a bit of floating floor. Also want to put up a frame for a shed out the back. All materials are here and what isn't will be supplied. Lots of small jobs so hourly rate only please.

Dual swinging cabinet doors have ripped off at the hinges. Need to be reinstalled but will need to have some modifications as the screws have damaged the fixing base. A job for a cabinet maker not a handyman.

Build and install a single cabinet, no doors, for the space above the fridge.

Open kitchen cabinet 4 shelfs measuremnets are ; H 163 cm x W 35 cm x Depth 35

I have a new Westinghouse dishwasher that does not fit easily into current dishwasher underbench cavity (image 1). Whilst the dishwasher would fit, the cavity is slightly out of alignment and is a squeeze. I suspect upright cabinet support to right may need to be removed. Not sure if upright screwed or glued. New holes for dishwasher inlet & drainage pipes would then need to be drilled to bottom right of dishwasher cavity. Pipes would go under kicker to the right and up through another hole that would need to drilled in floor of rear right under sink (image 2). I think this needs a qualified cabinet maker/joiner. Whilst you are here I would like to get quote to look at planing bottom of back of linen cupboard door as it is catching on the bottom (see images 4+5).

Hi, I need help on removing an old, top section kitchen cabinets (about 1200mm 3 doors) and an old pantry (1800mm height, 400mm width) all attached to the walls. Including rendering the parts of the walls where the cabinets were attached.

I need to replace two corner kitchen cabinet doors. Please include cost of doors and all inclusive costs in your offer.

Hi, I need to create a space for a dishwasher to be installed. The baseboards of the cabinetry need to come out

Remove old vinyl cabinet covers and paint cabinets to match color of other cabinets

Kitchen cabinets, drawers and shelf painted. There are more cupboards and drawers that cannot be seen in the photo. On the left side there are 4 cupboards above the bench and 3 cupboards and drawers below the bench. Also a shelf above sink.

We have this rather wide kitchen cabinet that sits above our kitchen sink. It seems to have been a DIY project done prior to our ownership and was designed to work on some sort of “hydraulic” arm system so that the long cabinet doors would open out and then up rather than opening landscape outwards into the kitchen. These doors have fallen off due to them being broken and the arms being “stuffed…”. I don’t think there is much chance of reviving them so we’d like to effectively put in some new doors. Note in the images below we do have the original doors albeit their frames have started to fall apart. If repairable we’d be open to that, as it could simplify the job. We’re open to suggestions about what would work functionally best and look the best. It doesn’t necessarily need to be the “hydraulic arms” again if you have a better suggestion. We would like the solution to fit in with the aesthetic of the rest of the kitchen. “White and tidy”. The ideal taskee could both suggest and design something to fit and also build the doors and install. I’d be happy to lend a helping hold to hold things in place etc. Rough specs: 110cm wide per cupboard (~220wide for both) 47cm height PLEASE NOTE: **I know this isn’t a $99 job. That’s just a placeholder, as I’m not sure how to put a price on this when we don’t yet know what design or effort we’re looking for. If you’re able to provide a t shirt estimate of your time and rates per hour perhaps easiest to go from there.

Remove Vinyl wrap on a few mdf panels Make good to some mdf by removing glue Paint mdf kitchen cabinets

Two of our kitchen cabinet doors are warping and splitting from dishwasher heat. Need a skilled cabinet maker to source and replace the panels

Looking for builder/ handyman to adjust ikea kitchen wall cabinets to ensure they are up to new building regulations. Wall cabinets have been hung, however they need to be raised 100mm to accommodate the distance from the stovetop to the rangehood hood. The oven needs to be raised or benchtop lowered (currently 940mm high) so oven can be higher than benchtop. Price is based on 6 hrs work, possible you could finish it sooner depending on experience with ikea kitchen rail system. Your own tools and knowledge required. Apologies if you've seen this before. Completion in July preferred. Thanks!