Find a local Tasker to help you make a kitchen cabinet in Sydney

Recently moved. Our fridge is ~800 wide and doesn’t fit into existing cabinetry which is ~760 wide. Looking for someone to come and adjust cabinetry to fit the fridge.

kitchen cabinets see sketch for dimensions

4x low cabinets have been assembled, 1 more base 800x370 cabinet + fridge cabinet require assembly. I need the cabinets hung and levelled on wall. Feet also need to be installed. Must have laser level, packers + tools to complete job. Preference will be given to taskers who have experience with the Metod system. 🛠️

Our kitchen cabinets are high and deep making them awkward to organise and access. We'd like to add additional shelves to them to make them more useful. We’d also like to add more shelves in our wardrobes if possible too. Flexible on budget, I understand material and labour costs will vary. For the kitchen cabinets - looking at adding a shelf to the lower section to split it out a bit Main bedroom - adding shelves next to where the little flat pack one is now Bedroom 2 - add shelves where the vacuum is currently with enough space for the vacuum to go next to it if possible. Open to any suggestions and ideas :)

We need sour kitchen cabinet modified to fit a new fridge

I need to someone to make kitchen cabinet. Pls include materials,design etc.

Install cabinets and bench top, total 5 pieces , bench top needs to be cut to sizes ( 230cm x 58cm) and painted two coats.

re-install kitchen cabinets that have been removed

Hello. Pls refer to the images attached for details Long story short the cabinets are pretty old and cheap but this is what I’m doing so before anyone tells me to replace them etc. I don’t want to hear it lol. Read da job and decide if you can do it or not. I will reimburse/transfer the cost of all additional consumables and materials bits bobs required to finish this. 1. REPLACE MDF PIECE - under the sink had a leak that’s now been repaired but unfortunately I let it go on for long enough for the water damage to rot that base board part. I’ve removed it and gotten a new piece of MDF cut to exact size to replace it. I was going to use furniture brackets to drill in and use to support the new piece but those got moved to storage so it’s easier if you get some new ones or whatever idea you think will work to hold up an 80cm x 60 cm piece of MDF 2. PAINT BASE CABINETS - Finish/go over my amazing midnight manic piece of work I started. Primer and paint provided. Oil base. Should have some sand paper and rollers/paint brushes left behind but get what you need from Bunnings. 3. Readjust the new door hinges I did a meticulous job guesstimating with the drill. They’re not exactly level and the one with the drawers overlaps the door part so you can’t open it properly lol. The doors will fit. Just needs fine tuning 4. ATTACH HANDLES - easy part 5. FINISH STICKY TILES - easy part WORK BENCH: Yeah idk. It’s an antique/vintage timber bench and thought I’d fill in the groove markings and gaps to make a flat even sealed surface more appropriate for food preparation area so I poured Agnew’s Water Putty to level the gaps and didn’t quite think through what my next move would be. I would say it can probs be mostly removed with a sand and a simple cleaning and sealing of the timber would suffice. Make it look acceptable.

I am getting a new fridge and the space it goes into is slightly to small so need the shelf that the microwave sits on raised

I have six (6) cabinet doors to be installed in kitchen. Purchased doors from bunnings. Need to take hinges off old doors and fix to new

Build kaboodle kitchen cabinet and fit over fridge freezer and cut piece of cabinet out

Some of the drawers in my kitchen are looking old and need repairing or replacing (so long as we can get them matched to the others) - see images attached

I’d like the silver cabinets repainted to matte white to match the top cabinets

I am getting my kitchen doors and all visible cabinet exteriors painted. I would like someone with experience in carpentry/cabinetry to help me remove the cabinets for painting and then to help me put the kitchen back together a few days later

I need an experienced cabinet maker / kitchen installation person to adjust the cabinetry. The kitchen is only three years old and the cupboard hinges need aligning, the dishwasher facia, some drawer fronts. It is a custom made kitchen, but I am not sure its was installed well. I need someone with experience and an eye for detail to realign it. I expect its about 1.5-2 hours work for someone who knows what they are doing.

We have a small L-shaped Ikea Kitchen made up of 4 Method base cabinets. All cabinets, drawers and bases have been constructed. Would like someone to come and do the final installation of cabinets onto the wall, attaching bench top and the two cover panels. Looking for someone with prior experience with flatpack Kitchen installs (preferably Ikea)

Seeking a quote to assemble flat pack kitchen cabinetry and install in the kitchen once assembled. Date is approximate as delivery is yet to be confirmed. Photo of old kitchen for reference, will be the same shape but replacement of all cabinets. Benchtop will be installed separately.

Align and then screw three cupboards and oven cabinet to wall so benchtop can be put on. I think the wall is concrete. Kitchen has been finished but my installer ran out of time and gone on holidays. It’s a small job. Might have other jobs like putting on the push closets but can discuss after thx

I'm considering updating and replacing the kitchen cabinets in my home. Attached, you'll find photos for reference. The upper cabinets measure approximately 362cm in length. We are open to the idea of using premade cabinets and are prepared to cover the cost of materials.