Find a professional kitchen sink installation service in East Melbourne

Flexible H+C hose supply to Kitchen sink leaking. Probably at a joint in the Hose located in the cupboard under the Sink.

The kitchen sink edge is off from the bench. I need someone to fix that before today 4pm.

The hot water hose under the sink is leaking. I think it has a split in it and will need to be replaced.

Remove existing sink and replace with supplied sink ( as pictured ). Hole to be drilled in new sink and new mixer tap installed. The existing bench cut out may have to be slightly enlarged. Current Sink is 950mm long and new is 1000mm.

I need this tap unit replaced by a new one which is in the kithcen sink. This one is detached from the rotating knot thus making it hard to rotate, though I can use it by applying glue and stays together for a time being. Now I want a permanent solution of replacing it. I will supply another unit you just need to replace it.

The slab adjacent to kitchen sink is broken, need a carpenter/handyman to make a wooden slab then glue the kitchen slab pieces on top of it.

Kitchen sink drain is blocked. Not inside, in pipes in ground. I believe it’s grease blocking pipe in the ground. Easy access as IO is on outside wall. Need snake to clear it. In the ground Pipe does down 400, then a 90 deg bend

We got a new kitchen put in late 2021 and for the last 2.5 years it has had constant leaking problems. The builder replaced it once already but never resolved the issue. The screw parts unscrew themselves and we tried to fix it ourselves with plumber's tape to seal over the threading to stop it moving but that also didn't work. I am at my wit's end, with a container under the sink catching all the drips.

Kitchen sink drain going very slow also on of the showers upstairs

I just purchased a new kitchen sink tab and want a plumber to replace the old one with new. The new tab is Greens Galiano pull-down sink mixer. Thanks

I require my kitchen sink to be installed in my newly fitted out kitchen. The Benchtop is being installed today. The plumbing rough in is completed, I just need the below sink drainage, water inlets, kitchen tap to be fitted as well as having the infrastructure for the dishwasher. Obviously happy to pay for materials etc …I have the sink and tapware however would need two new inlet taps (one with a dual connection so the dishwasher inlet hose can be fitted) and would also require a P trap etc

Looking to replace existing kitchen double sink and mixer tap to a new one. New sink and tap to be purchased by me. To be installed over mount and new mixer tap with pull down. Can someone please quote to remove existing kitchen sink and mixer tap, confirm measurement and install new kitchen sink and mixer tap with pull down. All other materials required for installation and sealing to be provided by tasker.

Fast leaking old shower head want it fixed not replaced. Also reseal kitchen sink

I have a kitchen tap with hot and cold connections at bottom. There is a small water dripping in the cupboard when the tap is on. It may possibly be a washer or loose connection issue. I have got spare washer or even the spare pipe connection (if at all required, but unlikely). With my home tools, i am struggling to use spanner there, hence the call.

We are looking for someone to help fully unclog the kitchen sink , which gets clogged easily.

MUST HAVE A PLUMBING LICENCE. Accepting quotes for both jobs or just job 1 (toilet) by itself. Job 1 - Toilet Removal of existing toilet and installation of new Caroma Luna Cleanflush wall faced close-coupled toilet (I have purchased this separately). New toilet will need to be installed slightly to the left of existing toilet (approx 21cm from left-side wall). Ideally do not want to relocate the existing water supply tap (I think there should be enough clearance when using the Caroma Uni-Orbital connector). Note that base of the new toilet unit tapers inwards, so should measure slightly less than 35cm wide. See images for measurements. Relavant links: https://media.prod.bunnings.com.au/api/public/content/8212dc19db3d4932a201e598ed60d5ed?v=f21fa31e https://media.prod.bunnings.com.au/api/public/content/1bf9d0de57a7478a90e9707ddcaaf80f?v=6e4a2d4c https://www.caroma.com.au/products/caroma-uniorbital Job 2 - Kitchen Sink Replacement of existing sink with larger/deeper double sink and new mixer tap (I have purchased these separately). Existing sink measurements are 1230mm L x 470mm W x 130mm D (including drainboard 400mm L across). New sink measurements are 1250mm L x 500mm W x 205mm D. Piping will need to be reworked for the deeper basins, and some cutting of cabinet wood may be required for the deeper right basin. Relevant links: https://sinksworld.com.au/products/handmade-stainless-steel-kitchen-sink-double-bowls-with-drainer-125cm-x-50cm/ https://media.prod.bunnings.com.au/api/public/content/32f71bdd0cab4e2fb79c6a8c4d35e2ca?v=df0450f0

Install 1x kitchen sink tap

Replace bathroom basin taps X 2 and plug holes Replace kitchen tap Replace front garden tap Work after 6 or weekend only All taps and plugs supplied Please quote all inclusive

Kitchen sink has become blocked

Want to replace kitchen tap with the one I just purchased. See pictures Must have own tools.