A beautiful pool table with blue felt in a bright room with floor to ceiling glass windows.
A beautiful pool table with blue felt in a bright room with floor to ceiling glass windows.

Find an experienced pool table assembler in North Brisbane

Fill in a short form and get free quotes for professional pool table assembly services

4.3

Excellent rating - 4.3/5 (10900+ reviews)

When you need help with pool table delivery and assembly

  • Pool table setup
  • Snooker table assembly
  • Billiards table assembly
  • Refelt pool table
  • Pool table assembly
  • … or anything else
It only takes 2 minutes. And it's free.
Up to 50% cheaper than franchise dealers
No job too big or small
Free insurance coverage
Secure cashless payments
Same day or next day service at no extra cost

Best rated pool table assembly services near me

What is Airtasker?

Post your task

Post your task

Tell us what you need, it's FREE to post.

Review offers

Review offers

Get offers from trusted Taskers and view profiles.

Get it done

Get it done

Choose the right person for your task and get it done.

Now Available
  • Get it done now. Pay later.
  • Repay in 4 fortnightly instalments
  • No interest
  • Available on payments up to $1,500

What do pool table assembly services include?

Pool table assembly services include necessary steps to make your pool table ready for play. Specialists will go to your home and assemble the legs, corner frame and the frame, lay down the playing surface, cover the surface with felt, cut the ball pockets, install the railings and secure each part of the pool table with the supplied washers, nuts and bolts. Specialists will also work to ensure that it’s perfectly level for the years to come.

Assembling the legs, corner frames and cabinet

Assemblers usually follow the enclosed pool table assembly instructions. They will assemble each of the four legs and bolt them along with the supplied nuts, bolts and washers. They usually assemble the corner frames, cabinet and legs while ensuring they are flush and made secure with washers, nuts, bolts and wood screws. To finish, they place the corner trim pieces, making sure that these pieces are flush with the bottom and top of the cabinet. Specialists may do some minor sanding if the trim pieces aren’t flush with the cabinet.

Installing the inner frame

Next, the specialists install the inner frame beams. These will support the playing surface, usually consisting of three slate blocks. The usual practice is for specialists to lay down the wood beams and tap them into place with a rubber mallet. Specialists install the frames and ensure that the structure is both flush and sits level on the pool table cabinet.

Playing surface assembly

After installing the frame and ensuring its level, laying down the playing surface is the next step. The playing surface usually consists of three heavy sheets of slate. Slate support blocks are first bolted onto the inner frame to accommodate the playing surface. After that, specialists screw the three slate pieces onto the support blocks, using the pre-drilled holes on the slate pieces. Specialists can ensure that the slate pieces are flush and level, then seal the seams between the pieces with drywall spackling.

Installing felt playing surface

After assemblers fill the seams between the slate pieces with drywall spackling and allow this to dry, they clean the surfaces of dust and debris. They then drape green felt on the slate, and attach the felt section by section with industrial adhesive, pulling taut on the felt as they go. Assemblers then cover each of the pockets with the felt, smoothing out any wrinkles as they glue the felt down. They spray the felt with adhesive and clamp it down for a couple of hours.

Installing the Rails

The top wooden rails are laid out over the felt, with the leather ball pockets fitted onto the rails. Each piece of the rails and the six pockets are bolted together. Once assembled, the wooden rail frame is placed on top of the felt. This is then aligned with the notches for the pockets. Your assembler then bolts down the wooden rails, then attaches pocket screws to the wood-slate frame, completing the assembly.

Recent Pool Table Assembly tasks in North Brisbane

8ft pool table (3 piece slate) dismantled and reassembled

$900

Bridgeman Downs QLD, Australia

4th May 2024

Dismantle the 8ft pool table at 1 address and reassemble it at another. This is a 3-slate table. Experience and knowledge needed

Reassemble my old pool table

$180

Everton Park QLD, Australia

17th Mar 2024

I have an old 10 ball pool table (pub size 7ft x4ft) I need to have reassembled and put back into my rumpus room. It is currently stored in the garage in pieces. It is a chip board table not slate. It can be carried back in pieces to the rumpus room area and put together in there. There is plenty of space in this room to work from.

Juan did a great job reassembling my old pool table. It was a very big and heavy job and he was very competent. He was polite and really helpful. I would recommend him for any job and I would be happy to use his services again. Thank you Juan

Building pool table

$250

Wavell Heights QLD, Australia

30th Nov 2022

i have an 8ft slate pool table that i need to install. can you please assist with this? Pool table is from T&R sports

Pool table installed

$200

Bracken Ridge QLD 4017, Australia

21st Sep 2021

Pool table is in garage needs to be disassemble and reassembled in outdoor area

Pool table pockets

$20

Bracken Ridge QLD, Australia

25th Dec 2020

Need pool table pockets put in. Have the pockets but no other tools.

Moving Pool Table

$250

Carseldine QLD 4034, Australia

9th Dec 2020

Hi, I have a pool table that needs to be moved from Carseldine QLD to Cashmere QLD. This would need to be unassembled first, move and then assemble again. So one needs to know how it is done. It is a 8ft slate pool table. Plz check here. https://www.trsports.com.au/8FT-SLATE-SNOOKER-POOL-TABLE-POKER-AIR-TOP-p/spbk08blu-ak-8ahpk-ak-e-puck.htm