Find local power point installers in Baulkham Hills & Hawkesbury

1. Install new ceiling light in kitchen (including removal of current light) (new light in pic 1, current light in pic 2-3). 2. Fix power point (pic 4) - not sure why it doesn’t work. 3. Fix exhaust fan switch (pic 5) - power point works well, fan works well when connected separately, just that fan switch doesn’t work, need check and fix. (Fan in pic 6).

Need to replace 4 power points. To hang two outdoor room ceiling lights from existing light points. No re-wiring needed. Power points and lights are on site. Approx 2 hours of work

-One PowerPoint understair -Baten light/b22 bulb installation understair ( light bulb of B22 will be provided) -Fan installation subject to support bar if required in alfresco(fan will be provided) -powerpoint in alfresco

Quotes are sought for supply and install of a PowerPoint on an upstairs wall, so that I can use a TV. There is no PowerPoint in close proximity on the same side of the wall. However, on the other side of the wall, there is a PowerPoint on a perpendicular wall behind the bedside table as shown in the image.

Minor Electrical Task- Run a Power point inside a Cupboard

I need 2 power points back to back on either side of an internal wall. There is another power point 0.5 metres away that you can piggy back off. The third is at the back of an island bench in the kitchen. You can piggy back off of the dishwasher In the island 0.5 metres away. Supply and install please matching to the existing power points in my home. Photos can be supplied but I believe they are Clipsal iconic.

Install power point & light bulb point under stairs storage, power point is opposite of gyprock wall, so I believe it should able to utilise access to get connections but I will leave to experts.

To establish TWO power points on both sides of garage door(marked as x) & switch connected to the front one(marked as 0).

Hi want a double power point outdoor in the alfresco and a 15A power point in the garage and a few other things need to be checked thanq

3 x old bathrooms have been demolished and need the existing power points prepared for the tiler. There are 3 double power points and 2 function switches in total. They do not need moving at all. Tiles in the last image are being removed Saturday morning

Licenced electrician Replace current ceiling fan with a new ceiling fan with light. Removing current controller from wall. (Fan supplied) Install 2 double power points ( not supplied) in new locations of room Remove small wall light and plug.

change of cover of wall switch and power point s

We have a switch in the walking wardrobe for light, double storey house and this is on upper level so easy access. would want to add 1 power point next to the existing switch. Would want to do it without any patch work as painting is recently done

We have a current 3 phase power point on the wall in our workshop as pictured. We have a new heater that is 3 phase with a different plug on the end of it (as pictured) we need to keep the current 3 phase plug that is on the wall but add a new point next to that one to accommodate the thew plug (so there will be 2 plugs)

One of my Power Point board attached to the kitchen backsplash has come off. Need it fixed.

Looking for a licensed electrician to install couple of power points

A double power point installed , between two existing power points, on a gyprock wall on the inside inside of an external cavity wall.

I need wiring installed for two wall lights (to be fitted independently) in my bedroom. There are also two power points at floor level and these also need to be moved a metre or so to the left and right as they’re currently right behind the bed. Photo added of the wall. My blue circles are where we would like wall lights (maybe a bit lower actually). The existing power point needs moving to the left and one equal distance from the right hand corner also. There is roof access directly outside the bedroom if required. The existing wall will be overlayed with panelled sheeting once the wiring has been installed. Thanks

1. Relocate a 9-port Ethernet cable hub to the opposite side of the current wall. 2. Install five new Ethernet cable runs to each of the four bedrooms + rumpus on the same floor, and install new Ethernet RJ45 port sockets for them all, on wall plates at either ends. The cables will be run through the ceiling and connected to the new central hub. 3. Install four new electrical power points at the new hub location. Install two new electrical power points at the old hub location and a RJ45 data port. 4. Install four CCTV cameras. NO new cabling or additional power supply needed. All necessary infrastructure is already in place.

We have an electric power point that has come away from the wall. Need it attached correctly and legally to the wall by an electrician.