Find a professional render contractor near you

You will need to seal a few holes and then coat the render to match the surrounding surface as the brick has fallen apart in the process of drilling

I’m renovating my kitchen and need a skilled renderer to smooth out the wall in preparation for a new splashback. The wall has some imperfections that need to be addressed to ensure a smooth, even surface for the splashback installation. The area to be rendered is the kitchen wall where the splashback will go. The surface will need to be smoothed and prepped for tiling or installation of the splashback. Any existing holes or rough patches need to be filled in. Looking for a professional, reliable renderer who can ensure the wall is smooth and level. Job is to be done in June

Need help rendering side wall. Small job.

We are looking at getting micro rendered cement on the bottom half of 1 x wall and behind fridge on block work. Please see following dimensions for basecoat and rendered cement: Wall is 5.5m long x 1.4m high = 7.7m2 behind fridge is 1m long x 1.6m high = 1.6m2 Total 9.3m2 Product rockcote concrete finish or similar. Thank you

I have 2 garage walls that need to be rendered. Approx 35sqm

Render patch work needed. Need high build to the door jambs to enclose the entry. Windows will have infills above, and just render hard up (infills will not need rendering). Patch over exposed brick and if required, you’re able to render back to then timber post on the left. Doesn’t need to be coloured as will be painted over.

Job half finished, hasnt been able to return to finish the job.

I am after a rendered to remove all existing tiles on the balcony riser around 4.5m from ground level and render the entire area. This should be a 1 day job to do. I need an experienced and professional individual to do this task.

Looking to render the walls in our living room, including door opening.

Removed wooden gas box and need to render area two sides of gas meter on front verandah one side has render skirting.

I need a renderer with previously experience to go after my bad patchwork on the facade as shown! The widith is about 6M and the height about 4 m at the top with around 50cm around. Also to do the inside trim around the sliding doors. I have purchased the same rockcote two 15l drums so should be plenty

[[Previous task got cancelled due to assignee personal circumstances]] Looking for someone, be it architect, recent architecture graduates or final year students wanting some experience, I want to iterate through a few ideas for renovations of a two-storey house built in the 1970s in Brisbane. Foundation, brick veneer, on a slope. We don't have any official house plans etc so we would rely on your knowledge of house structures in that period that were built in Queensland. Not planning to submit DA or anything at this stage, I have a few ideas of what I might want to do and I need to visualise it to help me communicate and get quotes from tradies etc. If you're in town, more than happy for you to inspect the site and measure things with me, but otherwise I am happy to provide pictures and measurements. If you are familiar with Australia building code, it's a plus. If you have creative minds and can contribute ideas on how to make the house super modern, even better. The budget for this initial stage can't be shifted too much but it might have follow up tasks if I end up needing a proper drawing for DA or for a structural engineer approval. In your offer if you could indicate whether you're a registered architect/engineer in Australia (with registration numbers) that would be great, or if you're a graduate or final year student, which university are you from etc. Relative familiarity with australia building codes and structural practicality is important for exterior design. Have a look at references and see if our design language matches As an output to this task: Current state of the property 1x 3d render 1x 2d floor plan 1x 2d house plan incl exterior lot and slope Short term renovations (minor changes to current state such as kitchen, deck and stairs balustrade , retaining wall, Aircon, roof replacement, garage door, landscape) 1x 3d render Long term renovation (house extension, deck and fence changes, staircase movement, bathroom reno and flooring changes): 1x 3d render

Need to have someone render a section of exterior wall, rendered to match the current rendering texture. This matching is a must. This patch repaired area is from an old wall air conditioner that was removed. Right now I’m offering for this one small project. There are other areas that need work, but for now I’d like a quote for this render repair. Thanks. Size you can probably straight up see on photo based on bessablocks used.

repair/fill render around power points and chasing in old internal rendered wall after electrician has been today. This is for a kitchen renovation. Need job done asap.

I have three patches of wall that need a quick render to get us through to a renovation we will be doing in the next few months

I need an area of about 6 square metres rendered to match the thickness and finish of the rest of the wall. I'll paint it once rendered, so I just need a good finished coat that I can prime and paint. There's also a few other spots pictured (next to the yellow parts) that need filled in with render.

Looking for someone who can re-render the entire front fence.

Rendering of the shower walls, we provide all equipment, rendering experience required, 50$ per hour (2-3 hour job)

Repair exterior render (I believe it is a coloured silicone render) on area of building. Previous experience with material required.

Need to stall about 6 hooks into outdoor wall (cement rendered). It’s to hang out door lights.