Find a trusted window repair service in Collingwood VIC

Approximate Budget + Materials Need a service window cut into existing corrugated iron fence (approx. 2.5m wide x 660mm high) to create a secure tuck-shop style opening. The existing graffiti-covered iron must be retained intact as the openable flap, cut cleanly and safely. The following is required: • Supply and install full-length piano hinge along the top edge • Add gas struts, soft-open/soft-close lifters or arm supports so flap lifts upward and holds open safely • Fit locking mechanism to secure the flap shut when not in use • Strip and finish all cut iron edges to ensure no sharp or dangerous surfaces • Install simple, strong, non-wobble detachable counter on inside at service height – must lock down from the inside so it can’t be pulled loose or wobbled from the street side (area has high foot traffic and itinerants) • Prefer finished tonight (Fri 4 Apr) or must be 100% complete before 10am Sat 5 Apr – hard deadline Photos show the fence section to work on. Fence is part of the Berlin Brat Haus premises at 286 Smith Street, Collingwood. Power and lighting available on site. Quote must include all materials, labour and hardware. Needs to be clean, functional, and safe with a professional finish. ⸻ Let me know if you also want the final title, budget line, or add-ons like counter surface preference.

I live in a warehouse apartment and have pot plant sitting on the sale of my window which I would like help planted with the type of plant in the photo attached. I would like to see if this could already be grown rather than a seedling.

Servicing three windows all approximately 1m squared:  1 x Sash window that is a bit clunky to move up and down but it does stay open when opened 2 x Rod style windows (they don't have a cord/sash, they have a rod) that don't stay open when you put them up. We have to use a stick to keep them open.  Just keen to have all three windows moving as expected

Replacement of rotten window rails with new treated rails. Sourcing of material on builder.

repair or replace cut aluminium frame. Replace several aluminium snap on pieces

I need an experienced handyman to install fly screens for both a door and a window in my apartment. The fly screen materials will need to be provided by you, and installed securely. Measurements: • Door: 264cm (H) x 95cm (W) approximately • Window: 190cm (H) x 80cm (W) approximately Please provide a quote including the cost of materials and labor. Let me know your availability as well as any relevant experience with similar installations. Location: Collingwood

I have had a leak test report and they have found this window is leaking. I would like it to be resealed and a warranty of at least one year, more would be appreciated. I have put in $100 as a nominal figure please provide a quote.

One of the hinges has come off the window in the top corner, there is a piece to reattach it, but I don't understand if something else is missing. I'm writing $5 in the budget not to be disrespectful, I just don't know how involved this is to fix, happy to negotiate of course :)

URGENT HELP REQUIRED - We need to reinforce or reinstall around 15 hooks urgently (using the fastener style hooks) for displaying a hanging installation for our new store opening tomorrow (Saturday) morning. For one of the installations (see in picture), there are 8 hooks to be used - the current ones are too loose and need to be reinforced using the fastener or cup style hooks, whatever is appropriate. There are 2 other installations that require 4 hooks each (same style) - however those installations are much smaller and lighter than the ones seen in the picture. We need this done urgently (today morning / afternoon) - please contact me asap and I will respond straightaway. Regards, Dushyant

Old adhesive residue that has collected dirt over many years, 4 window frames to do. - Due date: Before Monday, 25 September 2023

To remove rotten exterior laundry door and replace with new solid core external door and repaint in existing colour. Exterior paint to be used. To remove damaged timber work covering telecom wires and replace with new timber work and repaint. To repair ground level windows and frames where possible and repaint in existing colour. Exterior paint to be used. There are 8 windows at ground level. - Due date: Before Monday, 24 July 2023

Remove then replace wooden window beadings. - Due date: Flexible

2 new hinges for a timber window and re-fit. - Due date: Flexible

We have one window louvre that has lost the nut, bolt and washer connecting it to the steel frame that aligns it and adjusts its position. On the other side of the window our motorised strut has also lots its connection to the frame of louvres. In both instances, its a matter of nuts, bolts and washers coming loose over time. Window louvres are attached to a large north-facing window on the second floor. - Due date: Flexible

We got some condensation coming from windows, three in total, creating mold around those three, and two of those have affected the wood floor with dark stains. We would like to fix the mold but also fix the floor if possible.

Hello, I need someone to advise and implement a method to hang 8 plants from the cornice of my bedroom window. The width of the ceiling of the cornice is 2 cm, and I was thinking of asking you to insert 8 screws (with hooks to hang plants) at regular intervals along the cornice ceiling (on the top inside). I am not sure what screws would be best, but if you advise, I can pick these up from Bunnings if you don't have them available. I thought another option might be to hang a rod below or within the cornice and hang the plants from that, but I am not sure which would be the best solution. Another option might be to insert the screws from the inside front of the cornice to provide room for adding a curtain rail later (as I think a sheer curtain may also help) - but I am interested to hear your thoughts. Thanks in advance for your help! Sarah - Due date: Flexible

Install a new piece of glass over this little window . This little bathroom window currently has two pieces of glass overlapping each other with a big gap (about 5cm) to vent the bathroom. It doesn’t vent effectively and it allows the cold air and noise to get in. I’d like to cover both pieces with one new piece to block out the whole window. Approximately 120cm by 30cm. Power point is close by. Ignore the plants- they can be moved.