Find wood fencing professionals in Melbourne

Need a Japanese-style wooden gate built including materials. Would like quotes with and without the top part as seen in the picture.

Hello. We need our wooden pailing fence between our yard and the next door neighbours replaced (approx 9m). We also need our back yard fence which backs onto a right of way replaced approx 5.2m. This section of the fence has a gate which can be reused.

Hi Seeking an experienced Fence installer as follows, There are two parts, Supply and Instal and Demolition, removal and dispose as follows, The Two parts are side by side 1. REAR (LHS) BOUNDARY FENCE - TREATED PINE PALING, USING HARDWOOD POSTS AND 4 RAIL SYSTEM Dimensions = 13.50m (length) x 2.25m (height ) 2.REAR (RHS) BOUNDARY FENCE - TREATED PINE PALING, USING HARDWOOD POSTS Dimensions = 10.80m (length) x 2.25m (height), Price OTHER - CORNER & STARTER POSTS Qty = 1.00, If you could provide a quote to complete the same within the next week or let me know any other details requried. Thank you Specific Job Details: Gates: - No gates needed Type of fencing: - Property fencing Materials: - Timber/Picket Site Visit: Anytime Thank you please include when you can do the task

Repair damage to wooden fence. Two rails are cracked and need replacement. One spans from post to post and is 270 cm in length. The other one spans three posts and is 540 cm in length. A vertical plank has to be nailed back in place. No painting is required.

We need to replaced damaged Pailing

Hi, we need someone to remove 3 wooden posts from our gate, remove the hardware and water hose from the posts, and remove 5 pieces of hardware from the house. I have tried removing these with a power drill and WD40 but haven’t been able to. Thank you for considering!

Put up fence extensions from bunnings, see link to product below. Fence length is approx 10m, has a small kink of about 30cm half way along. (see pic) I will pay for the extensions, just need someone to pick up from bunnings 5 mins drive away, and install. The bunnings extension is 460mm high, I need it about 300mm high, so need to shorten the extensions. Also need any off cuts etc removed. https://www.bunnings.com.au/lattice-makers-2400-x-460mm-fence-extension-paling_p0362694?region_id=116310&gad_source=1&gclid=Cj0KCQjwgL-3BhDnARIsAL6KZ6-VBbsGg7FrZA4HRVE4Bk9S0xtVnTHZGOSlRm5GY4wEWqwHkJsOSbUaAhbEEALw_wcB&gclsrc=aw.ds

Part of the wooden fence is sticking out, need it fixed so they are not sticking out. DONT NEED a new fence as we are going to renovate - we need to remove this potential hazard.

Have a wooden fence approximately 5 metres x 2 that I’d like to be rendered

We need: - an in-ground clothesline cut from concrete (no disposal required); - a new fold-down clothesline installed in the wooden fence (we have the materials); - a pull-up bar installed in a brick wall (we have the materials).

Hole in wooden back fence due to missing plank. Just need wood attached to cover up hole so can’t see in from outside. I have some wood planks that could potentially be used (see in photos)

Small wooden fence (2m x 3m) needs to be taken down and replaced at the back of property.

Wood fence has blown down. Need a temp repair and the whole fence replaced.

Replace fence and dispose of existing fence

Just need to re attach two wooden panels to the top and bottom of gate and would like to add some form of backing to said fence so you can’t see through the slats

Build a standard wood paling fence between two properties. Length 29M, at 2.1M height , the last 6M beside driveway at half height. Need to supply all the materials.

The gate post is too far from the gate and I need a 19mm timber fastened onto the post and have the gate catch that needs to be recessed into the timber.

I need (5) 1100x6000mm wire fencing panels brought from Toolern Vale to Collingwood. They are very light and only 5 of them, just very long.

The wooden gate on the side of the house leading to the backyard has fallen off due to the timber post it’s attached to splitting. I’m guessing the best way is to attach a wooden plank to the post to stop the splitting and then reattach the gate to the plank (open to other solutions). Will require measuring, cutting and drilling (and potentially a plank and screws). Additionally, the front gate needs to be realigned a bit so it closes more smoothly. This should be a quick 10 minute task.

We would like to get help building a 3x5x1.2m fence + swing gate around a new hot tub that we are getting delivered tomorrow. We have lots of wood already on hand from fences and decking that we removed a few months ago. We would love to also build a frame above the fence to trellis vines, but that's optional.