Find a local Tasker to help you make a kitchen cabinet in Sunshine Coast

We would like to add a row of cabinets to our current kitchen to take it up to the ceiling. We would like to follow the current configuration, one cabinet, add two cabinets to cover the exhaust area and three cabinets on the right. We would like to have the door profile the same as the doors with glass in the picture. Glass is not required, we will add a rattan insert on the inside. We would like to take the cabinets to the ceiling with a small bulkhead and a cornice the same as the current. Happy to connect direct to cornice if your prefer. We can supply the cornice. No painting is required. The dimensions are approx 2450 long x 320deep x 470high (to cornice). First cupboard is 500, the two over the exhaust would be 900 and the three cabinets is approx 1050 (including end panel). No internal shelves are needed. We would need to replace the end panel on the left (pictured) to cover both rows and this could be a flat profile. We would like the cabinet doors to cover the cabinet as per the current ones. We are ready to build whenever suits you and happy to confirm budget in person, but will need a solid estimate. Thank you

Carpenter Looking for kitchen cabinet co or an appropriately b/-licensed qualified carpenter /builder to organise a small breakfast bar addition to my kitchen. Some other small works too.

The new kitchen was badly installed 6 months and I need aomeone to fix it. The dishwasher door facade is not aligned woth the adjacent cabinets and is causing friction and it is nearly impossible to open. The skirting underneath the cabinets may need replacing.

We think it is under the kitchen zink cabinet. Acces is tricky and you might have to go through in built dish washer/ bottom of cabinet.

remove and dispose of approx 25 doors and drawer fronts and replace with new 16mm laminated.

I have a kitchen cabinet inserted in my van that I would like someone to cut down so I can fit a small refrigerator inside. I have a slider to use so it can be extracted.

We purchased a new oven that won’t fit in the same hole as the existing. Looking for someone to replace the piece of MDF that has the new dimensions cut into it as if we fit the new oven there will be a large hole at the top We would only be looking to replace the single piece, that holds the oven. Then our electrician will install the oven. see images for reference - Due date: Flexible

I need a small cabinet door replaced to match my existing kitchen - Due date: Before Thursday, 5 October 2023

Need to cut end bit of our kitchen cabinets to make space for a (free-standing) dishwasher. - Due date: Before Monday, 24 April 2023

My kitchen cabinet is too big for my new oven. I am looking for someone who can change the width of the cupboard. - Due date: Flexible

Kitchen island two way cupboard for appliances. Marble or stone bench top. - Due date: Flexible

Modify kitchen cupboards to fit dishwasher installation - kicks need cutting down to fit. Replace all kitchen doors. - Due date: Flexible

I am looking to change existing kitchen cupboards and need 3 cabinets made. 2 of them will each have an opening (590x450) to fit appliances. One an oven and the second is a dishwasher. A drawer for each one , either on top or bottom of the appliance. The third cupboard will be approximately 300mm wide. The existing cabinets will be utilised in another room , kickboard and bench top will be required for this. Approximately 1600mm length. - Due date: Flexible

Bought a small kitchen cabinet from Bunnings (brand Kaboodle) and need it installed on the wall as a floating cabinet. Cabinet has been partly assembled already as shown in photos, comes with the parts. Wall site has been measured/marked. Note: job requires stud finder. I think the wall may be concrete but I’m not sure!

Re installing Cabinet over the fridge and side wooden panel Re installing the switch for the garage on the wooden panel - Due date: Before Tuesday, 2nd Nov 2021

I'd like to get 3 overhead wall cabinets made up to match existing ones I have in my kitchen. I'm just after 3 cabinets: one 300 wide, one 965 wide, and one corner 600x600. All 730 high and 285mm deep (not incl door). Inner mid shelf 300 high. Doors 16mm thick gloss white.

We require a cabinet maker that can build kitchen drawers for an exiting kitchen.

- remove draw at bottom - remove oven - place the bar fridge in the space left. (May need to build a supporting panel at the bottom) - reduce overall height so that a shelf can seperate fridge and microwave with a top to finish it. All needs to sit back so that a door can cover it all....this will need to be made once we have measurement. I’m in the same complex as Northcoast kitchens who can make up any panels / fittings required. Just need somebody to modify. It’s pretty straight forward, just don’t have the time. I will be painting once complete

Upgrade cabinet front/doors