Find experienced local fencing contractors in Inner South West Sydney

Hi Airtaskers We are looking to put up a timber / wire balustrade / fence for a backyard deck. Deck material: Tiled deck over concrete slab. Deck size: 5.9m x 3.3m (approx) The fencing is to comprise of about 9 timber posts that are 90mm x 90mm. The timber posts are to be anchored into the concrete by a bracket which has a single 10mm x 100mm concrete screw. The wires for the fence are spaced at about 8mm up the post, with the post height being about 960mm. You will need to supply all tools for the installation of the posts (eg: drills, bits, hydraulic swager, wire cutter, etc). I will supply materials. Photos posted for context. Look forward to hearing from you and meeting you! Feel free to message with any questions

Need a 3 section colourbond fence installed and gate. Have the fence already. Gate will need to be built from the extra parts that I have.

We purchased a house and previous owners built a section of the fence around 2 shrubs it seems because they did not want to cut them. So i basically just want the little in and out bit returned to a straight line on both the side and back. Bit if a sloped block so i know it won’t be perfect but just want it to continue with existing level and line and be sturdy. Can just reuse the material here from the fence but may need a support post for the extended section if you please cost that into your offer. I will get the shrubs and stumps cut low before the work so no issues here. The size of the fence panels to move around are 1.4x1.6m . The fence height is 1.8-2m. The back fence is higher than the side fence due to the land slope. But ideally if i can match the height of the back to the existing back fence that would be good but if that won’t be stable enough then no issues as long as it is 1.8-2m heigh from the outside because needs to stay complaint for my pool

Supply and Install 6.5 m length and 1.5m height colorbond with door installed on concrete driveaway. Need matching color to existing.

Install supplied 88x88 post concreted into floor Will require to dig for post Supplied products -Concrete -3x 88x88 treated post - 180mm bolts and nuts

Front of fence hasshifted onto neighbours driveway. Now that the coco palm has bee removed, need the front panels of timber pushed back upright along the dividing line

Seeking for someone to supply and install a basic brown colorbond gate. Ideally, it will need to be installed from behind the veranda to the right side of fence. See red arrow in photo. Approx 2.2m in length give or take. Complete gate needs to be openable in order to fit a car as this is a driveway. Seeking reasonable quotes only. Please advise how you will install.

Dismantle & Take away old colourbond fencing ,do 7 new coredrills into concrete, supply & install 14.4m (6panels) new primrose colourbond fence panels, rails & posts plus 1 extra core drill & 2 posts. Regards George

Last 4 panels of the cream colour bond fence are leaning over and I want them straightened

Fencer- I need a colour bond fence erected- 14.4metres (6panels) primrose colour including 6 core drills.Also I need to 2 more posts replaced which requires 1 extra core drill & All rubbish to be removed off site .

I need to install (from scratch) a small backyard gate between the house wall and the timber fence. The gap is about 125 cm. Probably the installation of some sort of pillars will be needed. I would prefer the gate's design shown in the photo

Need quote for rear boundary colourbond fence 600mm extension panels. Just need extensions across 2 panels wide of the rear Bowral brown colour bond fence. Extended for privacy from neighbour who built non compliant patio to our rear boundary. Need quote and will request neighbour pay for half cost.

Rebuild the brick fence in the front

Either fix or source replacement for pool fence gate and lock, and install. (We will pay for products separate to the labour on proof of receipt )

The panelling on one side of the right hand post of the outside fence has come off. The post on the right is flimsy, the wood is rotting and I was considering just have the panelling replaced for the front however possibly the whole post needs to be rebuilt and replaced. If you are able to this type of work and can let me know what is best to do and a price that would be great.

We have two outdoor gates that need replacing. I would like them to be treated timber in a simple picket arch with a Z frame reinforcing the back. They will also need to be attached to the wall with hinges and latches. Gate sizes: Side garden gate 97 width // height approx 157cm https://www.bunnings.com.au/900-x-1800mm-gate-cypress-arch_p0124921 Pool gate Width 83cm // height approx 140cm There are prefab ones at Bunnings for $148 that will suit the larger size, but not the smaller. The smaller will have to be built or perhaps we can cut another Bunnings one to size. Will need you to purchase materials after we discuss design, build gates and install.

About 2.4m between house and existing fence. Need a fixed piece about 800mm-1m at the house and the rest gate plus a two way lock… also need a two way lock on an existing gate… I am located in Padstow 😀

Doing landscaping in backyard we dug up what seems to be old cement cheeting and some steel posts, 12m long and probably just under 1m high, looming for someone to cut the material the ground level and remove it

Just need fence mesh installed to current fence, already have the mesh. Just need your own tools

- Remove damaged timber rail / fence on front porch and replace with new rail /fence - best match existing.- New bolts. - Discard old timber