Find a professional fire door installation service near you

I am looking for someone to replace 3 regular doors with fd30 firedoors into the existing frames (they are all regular sized 762x1980) The new doors have already been purchased and will need to be routed to allow for 10mm intumescent strips. We would also need to have overhead door closers and new handles and latches fitted and hinges changed to fire rated hinges. The door stops will also have to be changed. All fixtures, fittings, doorstops and doors have been purchased and are on site. These 3 doors are all on the ground floor and there is easy access to the secure garden where there is lots of space to work on the doors. Also there is the potential to discuss fitting of further doors after. I am quite flexible with the date, but would prefer the weekend of the 15/16th of February if possible. (Sorry if you may have seen this task before, but the project had to be delayed due to a door arriving damaged and not having a chance to reply before the task expired - but now we are ready to go)

12 fire doors installed and old doors removed

We've just had new carpets fitted and now one of our doors does not fit. Needs trimming from bottom Is an FD30 rated fire door

need fire doors taken off and re adjusted - need fire strips put on, and extra hinges on each door need gap under fire door resolved - so they all open and close properly

4 or 8 fire door to fit in the intumescent smoke seal, take down, rout, insert, tream, and adjust to fit right.

6 x Fire doors need trimming after installing new carpets

Hello, We need a fire door Plaining and our front fire door fixing

I need to have 3 doors replaced to fire doors. I have the doors, seal strips, handles and closers on site.

I’m looking for someone to install one fire door between the kitchen and hallway, and three solid bedroom doors (not fire doors, but not thin or hollow). The bedroom doors should be basic white, 4- or 6-panel doors. I need someone who can: 1. Source the doors (or tell me which to purchase). 2. Install the doors according to the requirements below. Licence Compliance Requirements: 1. Fire Door (30-minute fire-resistant) between kitchen and hallway: • Must comply with BS 8214 (latest edition). • Needs intumescent strips and cold smoke seals (in door leaf or frame). • Must have a self-closing mechanism. 2. Bedroom Doors (three total): • Must be solid, sound, and close-fitting. • No thin or hollow-core doors allowed. Budget and Payment • My budget is for labour • I will pay for Materials separately. I’m currently in Australia for a few months, but my tenants occupy the flat, and my brother can be on-site for you. I’ll coordinate everything remotely to make the process as smooth as possible. If you have experience with fire door installations, can meet these licence requirements, and can source or advise on door selection, I’d love to hear from you. Please let me know your availability, estimated timeline, and any questions you may have. Thank you! ___ You should understand BS 8214: Timber-Based Fire Door Assemblies – Code of Practice for installation. Installation: • Proper installation is critical for fire door performance. BS 8214 specifies that: • Gaps between the door leaf and frame should typically be between 2mm and 4mm. • Intumescent strips and cold smoke seals must be fitted correctly within the door leaf or frame. • Self-closing mechanisms must be installed and adjusted to ensure the door closes fully and securely.

Need to hang cheap b&q door with lock installation

Handyman needed to attach hinges to door. And attach fire and smoke sealant to door.

Fire Door requires a mechanism so you can enter externally in the case of an emergency. Door is fine and has push bar release internally.

Need 2 fire regular bedroom firedoors installed by a certified professional

1) Door Please supply and install one internal FD30 fire door and closer. This is a new door so hinges needed plus any work to make door fit frame. See spec below and attached photos. Door must open into corridor (towards photographer) against wall on right. Door Spec: A new half-hour fire resisting door-set that meets British Standard 476, Parts 22, and 31.1 to the living room. The door to be fitted in accordance with BS 8214. Provide and fit a suitable self- closing mechanism, together with intumescent fire seals and flexible cold smoke seals. If separate intumescent and smoke seals are fitted the intumescent fire seal must be fitted to the risk side of the smoke seal. Intumescent seals may be fitted to either the door or the frame but must not be fitted within door stops. Door to frame clearances shall not exceed 3mm at the sides and head of the door and 8mm at the foot. 2) Alarms Supply and install 3 x mains powered smoke alarms and 1 x mains powered heat alarm. All interconnected via radio. Spec as below: Alarms Spec: A system complying fully with BS 5839: Parts 1 and 6 (latest editions) for a Grade D system, with LD3 coverage as follows: - Interlinked, mains-wired smoke alarms with integral battery back-up located in the escape route at each floor level - Additional interlinked heat alarm with integral battery back-up located in the kitchen - Additional interlinked smoke alarm with integral battery back-up located in any communal lounge On Completion: The installer is to provide a certificate of installation and commissioning and log book to the user in accordance with BS 5839 : Part 6. latest edition A copy of the certificate of installation and commissioning is required.

Fire Door Installation Required (x5 Doors) We are seeking a professional to carry out the following work: - Remove existing doors and frames - Install new fire-rated door frames, linings, and architraves - The top glass panel (above the x1 door frame) needs to be replaced or boarded up. - Fit and adjust self-closing mechanisms - Install intumescent strips, fire-rated hinges, and door handles - Ensure all fittings are compliant with fire safety standards You must provide a Certificate of Fire Door Installation confirming compliance with fire safety standards

Installation of 2no. Fire door sets to meet BS 8214:2016 and 1no standard door. Documentation to be provided by a Self-Certified Registered ‘Competent Person’ or Certified by a Registered Accredited Third Party unless exempted, that the requirements are met to satisfy Legislative requirements.

Install new internal fire doors x3

Door may be too tight so may need planing down and hinges may be may need to be adjusted fire door closure. Sorry.

Few cms taken off door- after new flooring had been laid door wont shut. 10 minute job

Hello im looking for company who can supply the frame and door and fit it also. Please see pictures for details.