Hire a trusted window repair service in London

I have 2x boxes for a 2 piece sofa. One is 54kg and one is 40kg. They didn't fit through the door, but they will fit this window. I'm looking for someone with a decent ladder to help me get it in. My plan is to lay the ladder from the window, then tie climbing rope to the box, and one person pulls it sliding up the ladder and the other pushes from the bottom. I have climbing rope and tape etc but not a decent ladder. I reckon it would take me + 1 or 2 people about 15 mins.

Window mechanism broken so does not fully work. Piece missing.

I have bought a Fly Screen for Windows, 2 Pieces of Mosquito Net Insect Mesh with adhesive tapes and I need to help to install it on my balcony please.

So two things with the window: You can see it shifted left by the first photo and then a small gap on the right hand side at the bottom. Then there is the lock - the handle doesn’t seem to engage the mechanism that controls the locking pins that slide into the metal groves around the frame. So it needs someone who can adjust aluminium frames windows and work on the locking mech.

The handle of a window has come off. Need a new one fixed. Another window has air coming in as seal not tight to edge. Need that fixed too. I do not know type of window or brand so this needs perhaps a site visit beforehand.

My balcony has scratches on it which need repairing

The window sill cracked and lost a section, it might need recasting and replacing. The pillaret also has a crack that needs repairing.

Our skylight seems to be leaking, need it to be inspected and see what the issue may be. Potentially sealant. Damp would need to be fixed and cleaned.

Window cannot be shut. Need repair.

I would like to remove the window and will have to remove the bottom bricks/concete to fit a new door in there. I will need someone with experience to do this task. Please get in touch if you are able to do this task. Photos of existing walls and new doors uploaded

I have moved to my new flat and both bedrooms windows do not fully close. I have applied GT85 oil everywhere but still doesn’t close. I believe that it need adjustment to fit properly. The windows is a VELFAC 200 Reversible window. The flat is a 4th floor.

WIndow has come off top hinge and needs repairing to allow window to be open and shut properly.

Need a window handle replacing.

Window hinges not closing

I need assistance with the following tasks at a property in Peckham Rye: - Replace downstairs cloakroom mixer tap with similar equivalent tap - Repair /replace downstairs cloakroom door latch (current latch becomes stuck) - Refix loose double powerpoint that has come away from wall in front living room next to couch - Replace silicone sealant around downstairs shower tray and upstairs bathroom around bath - Troubleshoot / replace (probably need to replace) bathroom fans in downstairs cloakroom and upstairs bathroom to be more effective / draw more air - Fix / tighten loose window handle in back upstairs bedroom - Add 2 missing cupboard knobs in back upstairs bedroom (just small plain round knobs to pull, not latched. There are currently some slightly enlarged holes where the knobs should be.) - Secure a fence panel that has come unstuck in the back garden (does not need to be pretty, just neat and effective) You will need to coordinate with tenants to access as I am currently overseas. I have provided some pictures but I don't have shots of everything currently - apologies for the quality of a couple of these. Please let me know if you have any questions. PLEASE NOTE: I posted this task before, but it was deleted when my account was temporarily locked :( My account is now activated again but I have had to repost from scratch. I have also added a couple of things to the task compared to before.

I have bought 2 bronze barrel-style window stops to replace old ones, which now need screwing into a sash window frame. It should be straightforward. You can see from the photos we had to remove old ones because we lost the key so the new holes will go under the circles you see in the photos. It should involve drilling 2 holes and screwing the barrels into the frame so that the stopper can prevent the window from opening past a certain point. I’ve also included a photo of another window to show you what it will look like when complete. Thanks

We need a handyman to just put a few things right for our end of tenancy: - Take down 2xblackout blinds and rehang the old ones - Touchup the paint from the blackout blinds. - Quick touch up of paint on some skirting’s and one door from cat scratching it (may need a quick sand/buff but we have all paint just need paintbrush etc) - Rehang TV on wall (I can assist with lifting it) This is just so we get our deposit back we don’t need a fancy job here just a quick touch up. Job can be done within the next 2 weeks.

Hi, we would need someone who can procure and install 90 degree hinges on 2 windows we have (see pictures). Existing hinges are 31cmx1.5cm and the new hinge already installed in one of the windows is 41cmx1.5cm (see pictures)

Please pop in and take a look at the window in the bedroom. I’ve had my handyman look at it and he couldn’t fix it. Once you take a look please contact me so we can discuss quote for further action.

Main Job Brief - Remove existing plywood boards that have been affixed and plastered over a window recess to cover a blind - Drill new holes to fit blinds one cm back - Install GRP/fibreglass cover (supplied by me) instead - drilling and screwing/bolting into window recess - Plaster over the covers to uniform finish and level with wall - Paint whole wall of bay windows - Paint a second wall Problem: - I previously installed plywood boards inside the front of window recesses which contained roller blinds, the blinds were affixed with a number of steel L brackets. (Photo 1, 2) - The longest section (around 260cm) has warped, cracking the plaster. (Photo 3, 4) - The board now pushes against the blind Solution: - Install a fibreglass/GRP profile instead of the plywood. The profile will be L-shaped so can be screwed into the top of the window recess without using brackets - It must be securely fastened across multiple points, and plastered over with a good plaster/wood filler to prevent cracking - The ends may be fastened with L-shaped brackets to the side wall if required - The profile should be sanded/prepared and painted to a uniform finish along with the rest of the wall - The blind should also be moved back around 1cm, to further minimise the chance it brushes against the GRP cover - There is only 9.5cm of space from the window to the end of the recess so space is tight Second Task - I'd like to run thin cables through the 2 wall corner sections connecting between the bay windows to power/charge the motorised blinds - This should be done without cracking the 2 shorter plywood blind covers that are in fairly good shape - It could be done by carefully running a channel and covering over or perhaps by drilling from both sides of each corner through the brick Third Task A second wall should be repainted in the same colour as the other wall. It's already well painted except for a few very small patches that have been incorrectly touched up with paint