How to install a ceiling fan: A step-by-step guide

Learning how to install a ceiling doesn’t have to be as complicated as you think! Once you have the right tools and know the steps, you can manage to put up ceiling fans in any room of your house, all by yourself!

This guide will show you how to install ceiling fans with downrods, light fixtures, and even in rooms without existing light setups! Read on to learn all the essential tools and steps to installing ceiling fans.  

Tools needed to install a ceiling fan

You’ll need a couple of things before you start installing a ceiling fan. You can usually find these in your local hardware store, or even in your home toolbox! 

• 6-foot ladder

• Cordless drill with various screwdriver bits

• 4-inch hole saw

• 7/8 inch wrench

• Stud finder

• Non-contact voltage tester

• Tape measure

• Wrench set

• Wire stripper

• Ceiling fan kit

• Downrod (for high or sloped ceilings)

• Retrofit ceiling fan box/brace (Electrical box)

• 4-inch round ceiling box cover

• Safety goggles

• Dust mask

• Pliers

• Oscillating tool

• Electrician’s pliers / needle-nose pliers

• Wire nuts

• Switch or remote control

• Wire connectors

How do you install a ceiling fan?

Installing a ceiling fan can seem like a long and complex process, but with a bit of know-how and your ceiling fan kit’s manual, it can be done! Do note that depending on your comfort level with wiring, you may need to get help from a local handyman or electrician for some steps listed here. 

Step 1: Do the pre-work

First, decide on a location for your ceiling fan, ideally one with a functioning ceiling light. If the spot you have in mind doesn’t have a ceiling light yet, you’ll need to contact an electrician and handyman to run an electrical cable to that part of the ceiling.

Note: Make sure that you get the correct ceiling fan size and downrod length for your room.

Step 2: Ensure safety

Put on the safety goggles and dust mask before you start installing the ceiling fan. Then, turn off the circuit breaker. This helps you avoid any accidents while installing a ceiling fan.

Step 3: Remove the ceiling light

Get up on the ladder and remove the shade and bulbs. Use the cordless drill to remove the light fixture. Then, use the voltage tester to check that there are no live wires. Untwist the wire nuts, then untwist the wire pigtails. Set the entire light fixture aside.

Step 4: Remove the electrical box

Since the ceiling light’s electrical box can’t support your fan, you’ll need to replace it with a more appropriate one. Detach the current box using an oscillating tool. Be sure to leave the electrical wires behind.

Note: Depending on the kind of ceiling you have, you may need to use a saw and clear out some debris and insulation inside.

Step 5: Replace the electrical box

Use a stud finder to locate a spot between two ceiling joists. Fit the electrical box between two joists. Then, pass the electrical wires through this new box and secure it with the cable connector. After this, attach the cover plate to cover the box and wiring.

Step 6: Install the mounting bracket

The next step is to set up the mounting bracket. This can be pre-attached to the ceiling fan’s decorative cover or canopy. If this is the case, screw the bracket into the electrical box using the included screws. Run the electrical wires through the openings in the mounting bracket. 

Step 7: Assemble the ceiling fan

If your fan has a downrod: Set the fan motor right side up and thread the wire through the downrod. Secure the downrod to the mounting collar using the included screws, pins, or locknuts. Fit the collar, canopy, and ball over the downrod. Push the pin through the holes, then lift the ball over the pin. 

If your fan has a flush mount: Attach the top housing, trim ring, and canopy onto the fan motor. 

Step 8: Hang the ceiling fan

First, make sure that all the attachments are secure. Then, ask an assistant to help you lift the ceiling fan. Slide the assembled fan into the bracket, and carefully lower it into place. You should rotate the motor until you hear the fan lock into place on the bracket. 

Step 9: Wire the ceiling fan

Wiring your ceiling fan may get a little complicated, so reach out to an electrician if you’re not confident with this step.

Cut and strip the wires using the wire cutters and strippers, then match and twist them together. Lay the two black wires together, then twist them using a wire nut. Do the same with the white wires. Ultimately, connect the ground wires to the electrical box using the included screw. Make sure the wires are securely fitted against the grounding screw.

Step 10: Attach the fan blades

Attach the blades to their mount. Then, connect the entire setup to the fan motor. You may need some help lifting these parts into place as you stand on the ladder. 

Step 11: Attach the light kit

If you’re installing a ceiling fan that includes a light kit, check the instruction manual for the steps on how to attach the light bulbs. 

Step 12: Connect the switch

Part of installing a control ceiling fan or switch-operated ceiling fan is setting up the connection. This can be done by replacing existing wall switches or rewiring the connection with the help of an electrician.

Step 13: Test the ceiling fan

Finally, turn on the circuit breaker and switch on the ceiling fan using a switch, remote control, or pull chains.

☞ Related guide: How much does it cost to install a ceiling fan?

Install ceiling fans in 1 easy step with Airtasker!

Finding it hard to install your first ceiling fan? Can’t figure out how to install a ceiling fan with a light kit? Don’t panic - ask a local handyman near you to help you out! Tap the “Post a task” button on this page and get offers and choose between highly-rated ceiling fan installers!