Step-by-step guide to installing shower screens

For those of us who spend a lot of time in the bathroom, shower screens have many benefits: There’s less mess when you take a bath, they’re easier to clean than shower curtains, and they give the space a more luxurious ambience in general. While you can hire a handyperson, installing shower screens is easy if you’ve got the time, tools, and proper instructions. Read on to find out how to install shower screens on your own. 

What do I need to install a shower screen?

• Glass shower screen installation kit
  - Includes glass screen, base track, hinge-side jamb, strike-side jamb, header rail

• Tape measure

• Pencil

• Plastic anchors

• Silicone sealant

• Screwdriver

• 3.8 cm pan-head screws

• Drill (with 0.48 cm masonry bit) 

• Hacksaw

• Metal file

Can I install a frameless shower screen? 

Yes, installing a frameless glass screen for your shower is possible. While both framed and frameless shower screens are usually made of tempered glass, it’s important to note that frameless screens have much thicker panes. They will also likely need a rubber stopper in the bottom so that water won’t leak out of the shower when you take a bath. 

How long does a shower screen installation take? 

For skilled handymen, experienced DIY-ers, or those who have a helping hand, the project’s completion time should be around 2-3 hours (excluding the time it takes for the sealant to cure). For first-timers, however, the process might take an additional hour or two, depending on their skill level. 

How to install a shower screen

Given all the benefits of having a shower screen, there’s no reason to hesitate to install one in your bathroom. You can hire a professional to get the job done or give it a go yourself. If you choose to DIY the project, keep reading to learn how to install a glass shower screen. 

Step 1: Measure your shower entrance

You first have to ensure that your glass screen will fit in your shower’s opening by getting accurate measurements. Using the tape measure, note the total length of the threshold, the length of the threshold’s halfway point, and the height of your bathroom wall.

If your wall is over 1.5 metres, you must buy a filler strip to ensure your screen is plumb (or perfectly straight) when installing it. Also, take note of the distance between the shower and other bathroom fixtures (e.g., toilet, sink) to leave space for when you open the screen.

Step 2: Cut, set, and secure the base track 

Using the hacksaw, cut the base track to match the length of the shower’s threshold. Then, use the metal file to smooth the piece down. Make sure that the base track closely fits into the stall opening and, using the tape measure, find the precise centre of the threshold and position it there. Use the pencil to mark the base track down, so you can easily recentre it if it ever accidentally moves. 

Once you know where to place the base track, apply the silicone sealant to its underside and secure it on the threshold. Let the sealant dry (which may take three or more hours) before proceeding to the next step.

Step 3: Install the hinge-side jamb 

Position the hinge-side jamb onto the base track, ensuring that it’s both plumb and flush (or perfectly flat) against the wall. Using the pencil, mark where the screw holes will be placed. Then, remove the hinge-side jamb and drill approximately 4.4 cm into the wall. Add the plastic anchors into the screw holes once done.

Afterwards, reposition the hinge-side jamb onto the base track and line the frame up with the screw holes. While holding the hinge-jamb steady, tightly fasten the pan-head screws with the screwdriver.  

Step 4: Install the strike-side jamb

Fit the strike-side jamb onto the base track and position it against the wall opposite the hinge-side jamb. Like with the hinge-side jamb, use the holes of the strike-side jamb to mark where you will drill 4.4 cm holes into the wall. Remove the jamb, drill the holes, and add the plastic anchors inside them once you’re done. Put the strike-side jamb back into place and then secure it onto the wall with the screws. 

Step 5: Mount the glass screen

Lift the glass screen with its hinge rail swinging out and slip the hinge rail onto the hinge-side screen jamb. Check if the screen is plumb before drilling 0.56 cm holes through the hinge rail’s screw holes and the jamb. Then, secure the glass screen onto the frame with the pan-head screws.

Step 6: Cut and position the header rail 

Using the measuring tape, get the exact length of the top of the screen fixture. Then, cut the header rail with the hacksaw in this exact measurement. After smoothing the piece down with the metal file, slide the header rail into place atop the screen jambs. If the header rail you’re working with has screw holes on its ends, screw these into place too.

Step 7: Test the screen for possible adjustments

After mounting the shower screen, take the time to inspect whether there’s any need to make minor adjustments. For example, if there are gaps or cracks in the screen frame where water can seep through, you may use silicone sealant to close them up.

On the other hand, if there’s any resistance when opening and closing the shower screen, you may need to check the tightness of the screws or whether the frame’s parts are all plumb, level, and flush.

Spruce up your bathroom with a shower screen

Now that you know how to install a shower screen, you can gauge whether or not you can undertake the project yourself. While the process may take some time and effort, the reward will be great for both you and your bathroom. 

That said, if you would rather reap the benefits of a shower screen installation without having to do all the hard work, Airtasker has got you covered. Post a task on the platform today to have a professional get the job done!