Find an experienced builder in Perth

We have a Shed coming from Stratco and I'm looking for quotes to do the end to end installation from preparing the earth works (its currently due to be installed on a grass patch), concrete slab, installation of the shed and any wiring). Happy to chat further re: requirements. Link: https://www.stratco.com.au/au/sheds--garages/garden-sheds/handi-hilander-garden-sheds/handi-hilander-garden-shed-hh4-4.00x2.63m-gutter-side-door-gun-metal-grey-hhgsty1hh4gu/ 4x2.6 (and 1.95 high) Access to the backyard is limited with a 1m width maximum through the side gate. Alternative delivery methods are welcomed.

We would like our current old asphalt driveway to be replaced with concrete. It’s about 3x4m

2.25m x 4.5m 'Tall' EasyShed. Has 1x louvre window and 1x fibreglass skylight. Organising the slab separately so just putting the shed together and fixing with the concrete fixings. But happy to receive a price for slab install as well. Shed is in the back corner of block so have gone a bit higher on budget to account for moving shed pieces from driveway up to back corner.

I am needing a limestone wall built in front of the existing redbrick wall as shown in the photos. The wall will be 4400 x 3100 and use 500x300x100 limestone blocks or similar. The intent is for the wall to flow on from the existing limestone wall creating a clean flashing point for a patio to be installed. Materials can be supplied by contractor or myself.

Repair some sections of crumbling bitumen to

Supply and install timber decking

Looking for someone to replace a failed rafter of my patio. The rafter is timber, approximately 2.7m long, 35mm by 85mm, and would need to be cut to shape to fit into the existing structure. Price offered would include the cost for the timber.

Autocad 2D draftsman who has experience working with kitchen cabinets and electrical drawings Quick job, budget is $120 all up i have the original DWG file , AutoCad

The edge of the paving has failed, and the pavers have moved. It requires to be redone.

We have a shed/workshop in our backyard that is asbestos that we'd like completely removed in line with asbestos removal standards. The shed measures roughly 4x6m

We are renovating our bathroom. We need someone to break the existing floor (tiles and screed, down to bricks). We also need to remove the existing plaster/rendering on the walls. Finally, all waste needs to be disposed off.

Pull down and rebuild pergola structure and install new roof sheeting. Supply labour and materials.

Sound proof room needing to be built Room to be built into warehouse. You can use ware house walls and roof for support as its very close to the right dimensions. Ceiling to be made sound proof also. 2x sets of double doors to be fitted into frame. We would assume its being contracted with sound check panels and sound roof insulation. We would like a price on 90mm frame and a price on double thickness frame on 2 side walls. Need task completed by end of dec

This wooden slat pergola is 3.7 x 4.8 m and thickly covered with ivy. Moving the half barrel flower box might allow it to be used over. There is driveway access and space on the verge for a skip. A machine could be used with care for the reticulation. Rats might be nesting in the ivy!

We are renovating our kitchen and laundry. There is a wall that we suspect is loadbearing and needs demolition. There is also a small tiny laundry cupboard which appears to be brick but we do not think this is loadbearing. We would also like to remove this as part of the demolition of the kitchen and laundry . Either going to knock down entire wall or just create a servery gap. We strongly suspect it is load bearing. Must have own insurance Will need a lintel/ beam spanning opening

Airtasker Ad: Skilled Welder Needed to Build Heavy-Duty Ramp Frame I’m looking for an experienced welder to help construct a robust frame for a ramp. Here are the project details: • Material: 76x38 mm patio tubing with 1.6mm wall thickness • Dimensions: • Width: 90 cm • Length: 300 cm • Rise: 55 cm • Structural Requirements: • Supporting cross bars at every 50 cm • Stable supporting feet to ensure durability and balance • Load Capacity: Must be capable of handling a pallet jack and a 500kg Chubb safe. • Finish: Must be professionally welded for strength and safety. Requirements: • Previous experience with similar projects or load-bearing frames is preferred. • Ability to deliver quality, professional welds for maximum stability. If you’re up for the task, please reach out with your experience and any relevant examples of past work. Thanks! (Price is negotiable as I am not sure how much materials would cost you and time.)

Needing an Absco narrow shed assembled off the side of my house.

I’m about to embark on a kitchen and laundry renovation with new tiles required throughout, I need to get rid of these Italian looking 70s tiles and also demolish the cupboards and remove securely the existing appliances.

Re seal paved driveway approximately 100m2

Need a qualified drafter to draw elevation of enclosed balcony with all the dimensions of windows and stud walls to meet local council's requirements.