Find a professional gate installation in Rosebud

need to replace 2 corrugated polycarbonate sheets to my garage roof. Cutting will be required to fit same size as existing. I will dispose of old sheets

Gate post on 1 side (not tall) needs replacing and then gate rehung (same address as pergola job also posted). Materials extra to labour. - Due date: Flexible

Front gate sensorreplacement - Due date: Needs to be done on Friday, 26 January 2024

I have 2 old properties next to each other in Rosebud that have some leaks from the corrugated roof. I would like someone to patch the leaks using waterproof patch and seal tape or flashing No 6 Damage The back half of the house is a flat clip lock roof which is at 1° then a corrugated roof transitions onto the clip lock roof at 28°. That a transition flashing is where the problem lies there are plenty of trees which spill all the leaves and debris on top of the roof which causes to dam up another transition flashing and floods into the house in that particular area. So with my assessment done on a roof that is in good condition,to make it safe and have a long life we need to give it a thorough clean run 12 m of protective storm seal underneath the corrugation fix up the join of the transition flashing - Due date: Flexible

Old gate is worn replace with new gate & side posts - Due date: Needs to be done on Saturday, 19 November 2022

Colour bond gates and fence - Due date: Flexible

Install gate. I need installation of a gate at my property to keep dog secure ASAP. Will need to come to measure, purchase gate and install. Will reimburse for cost of gate + labour (2hours $100) -Location in Tootgarook

We would to have an electric gate to be supplied and installed (about 4 metres x 2.1m high) and front fence all in aluminium. Side and rear fences possibly colour bond (37m length x 2.1m high x 2 and 10.8m length x 2.1m high), as well as remainder of front fence about 6m x 2.1m high (aluminium). - Due date: Flexible

The St George Imperial wall oven is an oldie but a goodie. We have had issues in the past with no power. The timer being the cause. We had to have it set in a certain position in relation to the oven clock in order for the oven to work. This time however the oven had no power mid use, we realized as we went to use the timer on Christmas day of all days. Were hoping it might just be something as simple as a fuse. - Due date: Flexible

New house where a fence has been installed to side instead of timber gate. Need removed and replaced with gate - Due date: Flexible

My back gate buckled it’s hinges and blew off in a storm. Need someone with a welder to reconnect the hinges. Just a welder and maybe a grinder is all that’s required. Quick and easy job. Any time this week

Require a front fence and gate in the Mornington peninsula region.

Last storm snapped my gate off the hinge at the weld which appeared to be completely inferior. Need someone to attend address and weld the hinges back onto the gate. - Due date: Flexible

Hi, I am looking for someone to dismantle part of my fence and x2 gate. Please see pictures for the parts we need dismantled. We also need the dismantled pieces in good condition so we can use them again. The posts that have been concreted into the ground also need to be removed. The gates can be easily removed from the hinges.

2 x Gate Panels are 200 x 180 each + 2 x Posts Weight approx 25KG each panel Must have blankets to protect from scratching

Put in a treated pine fence and gate from corner of the house to the fence. Approx 5 metres.

Hi, wanting to trim the peaks off the top of my gate - single carport width - so that it has a straight top. See pic.

X 2 steel gate panels + 2 x posts Width 102 x Height 234 Posts 4cm each.

Repair powertech sliding gate motor

I need a fence replaced and gates as well I will remove old fence need done ASAP